Publicidad
ASSEMBLY
1. Tilt Fan Head back. Put Plastic Rear Grill on Motor. (Figure 1)
2. Align Triangular "∆" cut in Plastic Rear Grill with triangular post
on top of front Motor cover. Fully seat Plastic Rear Grill and
secure with Plastic Nut turning Clockwise. (Figure 2)
3. Slide Blade onto Motor Shaft. (Align groove on blade hub with
pin on motor shaft.) (Figure 3)
4. To secure Blade, screw Spinner onto Shaft Counter
Clockwise until tight on blade hub.
5. With fan head in upright position, align Ornament of Front Grill
so it is horizontal. Insert bottom of Front Grill into Plastic Rear
Grill. Tab at the bottom of Plastic Rear Grill should fit between
spokes of Front Grill. Snap Front Grill into Plastic Rear Grill
beginning at the top and working down both sides.
Plastic
Blade
Plastic Rear
Rear Grill
Plastic Nut
Spinner
Front
Figure 1
Figure 2
Grill
16
1
5
4
7
6
3
11
10
19
18
Rev. F 10/09
4DA35B/9102B and 4DA36B/9106B
Grill
Motor
Figure 3
Groove
Pin
Figure 3
14
15
13
17
9
2
8
OPERATION
VARIABLE OSCILLATION: Pull oscillation knob on the rear of the
motor up. Turn fan head to left, right, or straight ahead. Push oscil-
lation knob down and fan will oscillate about the set angle.
VERTICAL ANGLE: To adjust vertical angle, tilt fan head up or
down, as desired.
SPEED: Speed is controlled by a rotary knob. (0) Off, (3) High, (2)
Medium, (1) Low.
POWER SUPPLY CORD: Plug power supply cord into a wall outlet
(AC 120Volts, 60 Hz).
MAINTENANCE
WARNING:
ALWAYS UNPLUG THE CORD BEFORE MOVING
OR SERVICING THE FAN.
WARNING:
DO NOT IMMERSE FAN IN WATER!
Pin
CLEANING:
Use a soft cloth moistened with a mild soap solu-
tion, such as liquid dish washing detergent. Dry ALL PARTS COM-
PLETELY before reassembling. After any maintenance or servicing,
completely reassemble unit as described in this instruction manual
before reconnecting to the power supply.
CAUTION:
Do not use gasoline, benzine, thinner, harsh clean-
ers, etc. as they will damage the Fan. NEVER use ALCOHOL
OR SOLVENTS.
LUBRICATION: Precision bearings are sealed at the factory for life
and will not require any further lubrication.
STORAGE: Store the Fan, with these instructions, in a cool, dry
place.
SERVICING
All other servicing, with the exception of general
:
user-maintenance, should be performed by an authorized service
representative.
REPLACEMENT PART LIST
REF
NO.
DESCRIPTION
12
.
QTY
1
Motor
2
Rotary Switch
3
Crimp Connect
4
Elevation Spring
5
Ratchet Plate
6
Neck Bolt
7
5/16-24 Hex Nut
8
Stand
9
Switch Knob
10
Bottom Plate
11
Power Supply Cord w/Plug
12
Front Grill
13
Spinner
14
Fan Blade
15
Plastic Nut
16
Plastic Rear Grill
17
Grill Ornament
18
Rubber Foot
19
Screw #8 X 9/16 PPH
2
PART NO. FOR MODEL
4DA35B/9102B 4DA36B/9106B
02035053
02035052
02055087
02055087
7091854
7091854
-
02090586
02010162B
02010162B
02090521
02090521
02090033
02090033
2010540P
2010541
2010131
2010131
2010313
2010315
02050009FPB
02050009FPB
02096217
020962141
2010093
2010093
2010008
2011013
2010359P
2010359P
2011212
2011200M
02010381A
02010381A
2010415
2010415
2090039
2090039
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2084067
Publicidad
