Mounting Instructions - Good Earth Lighting G9112-SSX-I Manual De Instrucciones

english
Preparation
WARNING: Shut off power at the circuit breaker or fuse panel before removing the old fixture.
Your Good Earth Lighting® xenon under cabinet light is the perfect lighting solution for
kitchens, bathrooms, bookcases, entertainment centers, and study areas. We recommend you
read through the instructions entirely before starting your installation in order to help you
understand all the steps and options regarding your particular installation.
This unit has a polarized plug (one blade is wider than the other) as a safety feature. This plug
will fit in a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician. Never use with an extension cord
unless the plug can be fully inserted. Do NOT attempt to defeat this feature.
SAVE THESE INSTRUCTIONS IN A LOCATION CLOSE TO YOUR LIGHT FIXTURE SO YOU CAN
REFER TO THEM AT A LATER TIME.
1. Turn off/unplug and allow to cool before replacing the bulb (lamp).
2. Bulb (lamp) gets HOT quickly! Use caution when turning ON and OFF.
3. Do NOT touch hot lens, guard, or enclosure.
4. Do NOT remain in light if skin feels warm.
5. Do NOT look directly at lighted bulb (lamp).
6. Keep away from materials that may burn, or melt.
7. Use with a 120V/G8 base bulb/20 watt or smaller.
8. Do NOT operate the unit with a missing or damaged guard or lamp containment barrier.
9. Use only insulated staples or plastic ties to secure the cords.
10. Route and secure the cord so that it will not be pinched or damaged when cabinet is
pushed to the wall.
11. Do NOT use an extension cord. Use a power strip with integral overcurrent protection to
supply other electrical devices or accessories in cabinet.
12. Keep cord or combustibles such as plastic, paper goods, and the like away from hot
lamp, lampholder, or reflector.
13. Position cabinet light with respect to cabinet so as to permit reading of the lamp
replacement markings during relamping.
14. Not intended for illumination of aquariums.
15. Not intended for installation in plastic cabinets.
16. Not intended for recessed installation in ceilings, or soffits.
17. Do not conceal power cord inside a wall, ceiling, soffit, kitchen cabinet, or similar
permanent structure.
18. Do NOT attempt to install while plugged in.
19. For INDOOR USE ONLY.
20. Do NOT mount the xenon lights to cabinets having a material thickness less than 1/4 in.
21. Do NOT install these lights inside of enclosed cabinets.
22. Do NOT mount over sinks or stoves.
DO NOT INSTALL THE FIXTURE WHILE IT IS PLUGGED INTO AN ELECTRICAL OUTLET! FOR
INDOOR INSTALLATIONS ONLY. DO NOT INSTALL OVER SINKS, OR STOVES.

Mounting Instructions

1
To make installation easier, a template has been included on the back insert card of the
package (the card with the UPC code on it). The template provides the center-to-center
distance where the mounting screws should be located. Cut along the dashed line,
position and tape the template to the surface where the fixture is to be installed. Drill a
small diameter hole where the lines cross to make a "+" in the center of each circle on
the template. Remove the template from the mounting surface. NOTE: Be sure to allow
enough space for the fixture to fit and be plugged-in.
2
Fig. 1
3
surface. If not, then your screws need to be tightened a little more for an improved fit.
4
Fig. 4
Bulb Replacement Instructions
Replace with 120V, Type G8 base xenon bulbs, 20 Watt maximum.
1
Turn the light bar off and allow sufficient time for the unit and bulb (lamp) to cool
properly before handling.
IMPORTANT SAFETY INSTRUCTIONS
Place the two small rubber grommets over the mounting screws (Fig. 1).
Screw in the two #8 mounting screws until the rubber
grommets contact the bottom surface of the
cabinet (Fig. 2). Then turn the screws another 1/4
turn. The screws must be driven in straight for the
light bar to mount properly.
Fig. 2
Align the key hole slots on the bottom plate of the light bar
over the mounting screws and firmly slide the light bar
over in one direction to lock it into place (Fig. 3). The light
bar can slide toward the front, rear or from side to side
depending on the spacing in your particular installation.
Fig. 3
The light bar should fit tightly up against the mounting
Once the light bar is in place, route your power cord to the
closest outlet. Your xenon light bar has a three position
rocker switch on the face of the unit. The center position is
the 'OFF' position. The other two positions offer you a 'HIGH'
or 'LOW' light level setting depending on your needs (Fig. 4).
- 2 -