Makita 6226D Manual De Instrucciones página 4

ENGLISH
1 Button
2 Battery cartridge
3 Charging light
4 Battery charger
5 Tighten
6 Sleeve
7 Ring
8 Switch trigger
SPECIFICATIONS
Model
Capacities
Steel ............................................................10 mm
Wood ...........................................................21 mm
Wood screw .................................................5.1 mm x 38 mm
Machine screw ............................................6 mm
-1
No load speed (min )
High .............................................................0 – 1,100
Low ..............................................................0 – 350
Overall length .................................................210 mm
Net weight ......................................................1.4 kg
Rated voltage .................................................D.C. 9.6 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is used for drilling and screw driving in wood,
metal and plastic.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY
CARTRIDGE
1. SAVE THESE INSTRUCTIONS — This manual
contains important safety and operating instruc-
tions for battery charger.
2. Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
3. CAUTION — To reduce risk of injury, charge only
MAKITA type rechargeable batteries. Other types
of batteries may burst causing personal injury
and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold
by the battery charger manufacturer may result
in a risk of fire, electric shock, or injury to per-
sons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when discon-
necting charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress.
4
All manuals and user guides at all-guides.com
Explanation of general view
9 Reversing switch lever
10 A side
11 B side
12 Clockwise
13 Counterclockwise
14 Low speed
15 High speed
6226D
8.
9.
10. Do not disassemble charger or battery cartridge;
11. To reduce risk of electric shock, unplug charger
ADDITIONAL SAFETY RULES FOR CHARGER
& BATTERY CARTRIDGE
1.
2.
3.
4.
5.
16 Speed change lever
17 Adjusting ring
18 Graduations
19 Drill marking
20 Pointer
21 Screw
22 Set plate
6227D 6228D
10 mm 10 mm
24 mm 24 mm
5.1 mm x 63 mm 5.1 mm x 63 mm
6 mm 6 mm
0 – 1,100 0 – 1,100
0 – 350 0 – 350
210 mm 210 mm
1.5 kg 1.6 kg
D.C. 12 V D.C. 14.4 V
Do not operate charger with damaged cord or
plug — replace them immediately.
Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in
any way; take it to a qualified serviceman.
take it to a qualified serviceman when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock or fire.
from outlet before attempting any maintenance
or cleaning. Turning off controls will not reduce
this risk.
Do not charge battery cartridge when tempera-
ture is BELOW 10°C (50°F) or ABOVE 40°C
(104°F).
Do not attempt to use a step-up transformer, an
engine generator or DC power receptacle.
Do not allow anything to cover or clog the
charger vents.
Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as nails,
coins, etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.