EGO LM2120E Manual Del Operador página 15

WARNING:
To reduce the risk of injury, never
attempt to override the operation of the switch or self
propel system. Use the self propel for its intended purpose
only.
LED HEADLIGHTS (Fig. A-7)
Press the switch button (Fig. C-22) to turn on/off the LED
headlights in the front of the battery compartment.
POWER INDICATOR ON THE MOWER (Fig. S)
The mower is equipped with a power indicator to indicate
the charge status of the battery pack and the working
status of the mower. The power indicator will illuminate
when the blade is rotating or when the LED headlights are
turned on.
Power
Indicator on Meaning
Mower
Mower is working
properly; battery
Shining green
has at least 15% of
its charge
Shining red Low battery
The battery is
Flashing red
nearly depleted
The mower or the
Shining
battery pack is
orange
overheated
Flashing The mower is
orange overloaded
MOWER OVERLOAD PROTECTION
To prevent overload conditions, do not try to remove too
much grass at one time. Slow down your cutting pace or
raise the cut height.
Your mower has built-in overload circuit protection. When
the mower is overloaded, the motor will stop and the
power indicator on the mower will flash orange. Remove
the battery pack from the mower. Check to see if grass
has collected beneath the deck and clear it if necessary,
then install the battery and restart the mower.
BATTERY HIGH TEMPERATURE PROTECTION
The battery pack will generate heat during operation. The
heat dissipates more slowly in hot weather. If the battery
56 VOLT LITHIUM-ION CORDLESS MOWER — LM2120E / LM2120E-SP
temperature exceeds 70°C during operation, the protection
circuit will immediately turn off the mower to protect the
battery pack from damage. The power indicator on the
mower will shine orange and the LED on the battery will
flash orange. Release the bail handle, wait until the battery
pack cools down to approximately 67°C , then restart the
mower.
MAINTENANCE
remove the safety key from the mower before cleaning,
performing any maintenance or transporting the mower.
replacement parts. Use of any other parts may create
a hazard or cause product damage. To ensure safety
and reliability, all repairs and replacements should be
Action
performed by a qualified service technician.
CLEANING THE MOWER
The underside of mower deck should be cleaned after each
N/A
use, as grass clippings, leaves, dirt and other debris will
accumulate.
Stop the mower and
Remove any build-up of grass and leaves on or around
charge the battery the drive shaft (only LM2120E-SP) and the motor fan (do
pack not use water). Wipe the mower clean with a damp cloth.
Stop the mower and
REMOVING/INSTALLING THE BLADE
charge the battery
pack
Remove the battery
heavy gloves or wrapping the cutting edges with rags or
from the mower,
other materials when performing any maintenance on
move them to the
the mower blade. Always remove the battery pack when
shade and cool
servicing or transporting the mower.
them at least 15
◾
To Remove the Blade
minutes
Following Fig. T.
Slow down your
pace or raise up
NOTICE:
the cut height to
loosening the bolt, turn the fan by hand to align the
decrease the load
through holes in the fan with the holes in the blade,
and place another metal rod into the aligned holes
(Fig. U).
◾
To Install the Blade
Following the assembly sequence in Fig. V , with the
fan blade towards deck and the printed blade side
towards outside, align the through holes in the fan with
the holes in the blade (Fig. W) and then tighten the
blade as Fig. X shown.
Fig. U & V parts description see below:
WARNING:
To avoid serious personal injury, always
WARNING:
When servicing, use only identical
WARNING:
Always protect your hands by wearing
If the bolt rotates with the motor shaft when
EN
15