Publicidad
3
LED Mode
A) LED POWER: Acceso fisso -> Alimentazione YO/YC TU corretta.
A1) Lampeggiante sincrono con sganciatore Ekip Emax 2-> Comunicazione stabilita (Dip-switch COM ON).
A2) Lampeggiante asincrono con sganciatore Ekip Emax 2-> Comunicazione non riuscita (Dip-switch COM ON)
B) LED OPEN: Acceso fisso -> Bobina/coil switch assente, alimentazione assente o insufficiente, cavi interrotti, bobina/coil switch
guasto.
C) LED SHORT: Acceso fisso -> Coil switch guasto, cavi in cortocircuito. Solo per TMAX, XT2, XT4: Attenzione!
il cortocircuito non viene rilevato quando l'attuatore in prova è YO/YC (dip-switch TMAX,XT ON).
D) LED OPEN e SHORT lampeggianti alternativamente: malfunzionamento bobina/coil switch o alimentazione errata.
E) LED OPEN e SHORT spenti: Funzionamento bobina/coil switch corretto.
RESET: Rilascia il relé allarme K in posizione OK(KT3) se il guasto è stato riparato e se il dip-switch K LATCH
è abilitato. E' possibile rilasciare il relé anche tramite Ekip connect.
LED Mode
A) POWER LED: On fixed -> YO/YC TU power supply correct.
A1) Flashing in synchrony with Ekip Emax2 release -> Communication established (Dip-switch COM ON).
A2) Flashing not in synchrony with Ekip Emax2 release -> Communication unsuccessful (Dip-switch COM ON).
B) OPEN LED: On fixed -> Coil/coil switch absent, power supply absent or insufficient, interrupted cables, coil/coil switch failure.
C) SHORT LED: On fixed -> Coil switch failure, short-circuited cables. Only for TMAX, XT2, XT4: Warning !
short-circuit is not detected when tested actuator is YO/YC (dip-switches TMAX,XT ON).
D) OPEN and SHORT LEDs flashing alternately: faulty coil/coil switch or incorrect power supply.
E) OPEN and SHORT LEDs off: Coil/coil switch operation correct.
RESET: Releases alarm relay K in OK position (KT3) if fault has been repaired and if dip-switch K LATCH is enabled.
The relay can also be released by means of Ekip connect.
LED Mode
A) LED POWER: Fest an -> Stromversorgung YO/YC TU korrekt.
A1) Synchron mit Auslöser Ekip Emax2 blinkend -> Kommunikation hergestellt (Dip-Schalter COM ON).
A2) Asynchron mit Auslöser Ekip Emax2 blinkend -> Kommunikation misslungen (Dip-Schalter COM ON).
B) LED OPEN: Fest an -> Spule/Coil Switch nicht vorhanden, Stromversorgung fehlend oder unzureichend, Kabel unterbrochen,
Spule/Coil Switch defekt.
C) LED SHORT: Fest an -> Coil Switch defekt, Kabel kurzgeschlossen. Nur für TMAX, XT2, XT4: Achtung!
Der Kurzschluss wird nicht erfasst, wenn der getestete Aktuator YO/YC ist (Dip-Schalter TMAX,XT ON).
D) LED OPEN und SHORT abwechselnd blinkend: Betriebsstörung Spule/Coil Switch oder Stromversorgung falsch
E) LED OPEN und SHORT aus: Betrieb von Spule/Coil Switch korrekt.
RESET: Lässt das Alarmrelais K in Position OK(KT3) zurückfallen, wenn die Störung repariert worden ist und wenn
der Dip-Schalter K LATCH freigegeben ist. Es ist auch möglich, das Relais mit Ekip Connect freizugeben.
YO-YC Test unit | ABB
LED Mode
STATE
KT1-KT2
A1
OK
Open
A2
OK
Open
B
ALARM
Shorted
C
ALARM
Shorted
D
ALARM
Shorted
E
OK
Open
KT2-KT3
Shorted
Shorted
Open
Open
Open
Shorted
Publicidad
