Publicidad
Enlaces rápidos
Installation Manual -R007
Garden Feature Nook
YM11560
(1.99m)
Yardistry Ltd. - North America
Toll Free Customer Support: 1.888.509.4382
info@yardistrystructures.com
(1.18m)
(1m)
www.yardistrystructures.com
Yardistry / Selwood Products - Europe
Customer Support: +44 1284 852569
(2.17m)
parts@selwoodproducts.com
www.selwoodproducts.com
Revised 04/06/2011
1
Publicidad
Manuales relacionados para Yardistry YM11560
Resumen de contenidos para Yardistry YM11560
- Página 1 Installation Manual -R007 Garden Feature Nook YM11560 (1.99m) Yardistry Ltd. - North America Toll Free Customer Support: 1.888.509.4382 info@yardistrystructures.com (1.18m) (1m) www.yardistrystructures.com Yardistry / Selwood Products - Europe Customer Support: +44 1284 852569 (2.17m) parts@selwoodproducts.com www.selwoodproducts.com Revised 04/06/2011...
-
Página 2: Important Safety Notice
Tools Required Warranty: Yardistry Limited products are backed by a 5 year limited lifetime warranty from the date of original retail purchase for manufacturing defects and if installed as per manufacturer’s installation instructions. • Tape Measure •... - Página 3 A = B+C (90"- 96") Material List 4 x 8 Arbor Roof Kit includes: Nominale Actuel Post must be securely 4 x 8 Arbor Roof Kit includes: Nominale Actuel installed to support structure. 2" x 4" 1½" x 3½" Kit de techo de la pérgola de 4" x 8" incluye: Consult local building 2"...
- Página 4 Material List (8) One High X Topper (4) Two High Lattice Panel (4) Two High X Panel (4) 4x4 Post...
- Página 5 Step 1- Assemble Screens for Main Wall 1. R emove the upper metal connectors on both sides of PL2 - Two High Lattice Panel. Reattach the metal connectors to PL2 by securing the bottom two holes of the metal connectors to the top two holes on PL2 so that the metal connectors stick out from the top. Slide PX1 – One High X Topper between the two protruding metal connectors on the top of PL2. Attach the metal connectors to PX1. (Fig. 1A) *Ensure Panels are oriented correctly! (Fig.
- Página 6 Step 2- Assemble main Wall Fig. 1 1. Assemble panels together in configuration shown. (Fig.1) Insert male connector into female. Slide down until flush with adjacent Instruc Assemble Toppers to Panels. Pautas básicas para pour l' panel as shown. (Fig. 1A) Basic Guidelines el ensamblado de Instale los topes en los paneles. Instructions de base Cut and atta des pa...
- Página 7 Step 3- Assemble Side Walls 1. R emove the upper metal connectors on both sides of PX2 - Two High X Panel. Reattach the metal connectors to PX2 by securing the bottom two holes of the metal connectors to the top two holes on PX2 so that the metal connectors stick out from the top. Slide Px1 – One High X Topper between the two protruding metal connectors on the top of PX2. Attach the metal connectors to Px1. (Fig. 1A) *Ensure Panels are oriented correctly! (Fig. 2.
- Página 8 Step 4- Assemble Side Wall Fig. 1 1. Assemble panels together in configuration shown. (Fig.1) Insert male connector into female. Slide down until flush with adjacent Instruc Assemble Toppers to Panels. Pautas básicas para pour l' panel as shown. (Fig. 1A) Basic Guidelines el ensamblado de Instale los topes en los paneles. des pa Instructions de base for Panel Assembly...
- Página 9 Step 5- Attach Panel Clips Back posts 1. O n a flat surface place P- 4x4 Post on its side and position Panel Clips in Fig. 2 locations indicated in Figures 1 and 1A. Ensure Panel Clips are oriented as shown in Diagrams! 2. Panel Clips should be placed in the centre of the post or the leading edge of the clip should be 1 3/8”...
- Página 10 This identifies information that requires special Check that set or assembly is properly level Step 6- Attach Panels to Posts attention. Improper assembly could lead to an before proceeding. unsafe or dangerous condition. Pre-drill 1/8” & 3/16” Bit Where this is shown, 2 or 3 1.
- Página 11 Distance Assembly before tightening bolts. This indicates time to tighten bolts, b deck with the Yardistry Post Base (YM21016) or equivalent hardware. 177 " 177 " not too tight! Do not crush the wood. Use a measuring tape to assure 2. I nstall Post Top Connectors with S6- 1 1/2” Pan Head Screws provided. (Fig. 2) Ensure the...
- Página 12 Step 8- Assemble Roof Project A Proyecto A Projet A Y50113-029 1. A ttach two A- 2 x 4 x 80” Beams to Post Top Connectors with WH-7/16" Hex Bolt as shown in Fig. 1 and 1A. (2) 2 x 4 x 80" 2. C entre two B-2 x 4 x 41 1/8” Beams in place and attach to Post Top Connectors with WH-7/16" Hex Bolt as Y50113-031 shown in Fig. 1 and 1A. Drill 1/4” Holes for bolts using holes in Post Top Connector as guides. (36) #10 x 1"...