TECshow NAVIGATOR 3+ Manual De Usuario página 5

5. JOYSTICK SET UP
Assign Joystick
1. Press and hold down the Program button for
approximately 2 seconds or until the PROG
indicator in the LED display flashes. Once the
indicator is flashing, record mode is engaged
and you may release the Program button.
2. Press and hold down the MODE button and
then tap the FINE button.The "Assign" and
"Pan" LED's should illuminate.
3. "Assign Joystick Reverse" (Pan/Tilt Invert)
Operation Guide Select the fixtures that you
wish to assign the "Pan" for by pressing the
FIXTURES# buttons, 1-12, so the selected fixture
LED´s illuminate.
4. Press the Tap/Disp button to switch between
"PL.XX" & "PH.XX". "PL.XX" represents the Low
Byte or Fine channel, generally listed as the Pan
Fine channel and PH.XX represents the High Byte
or Coarse channel, generally listed as the Pan
channel. Set it to "PH.XX" and press and hold
down the MODE button and then tap the SCENE
button that corresponds to the Pan channel of
your fixture. For example, if your fixtures Pan
channel is 1 then you´d press the SCENE #1
button. Please refer to the fixtures DMX chart. If
your fixture includes a pan fine channel, press
the Tap/Disp button so the display reads "PL.XX.
Press and hold down the MODE button and then
tap the SCENE button tha corresponds to the
Pan Fine channel of your fixture. For example,
if your fixtures Pan Fine channel is 2 then you´d
press the SCENE #2 button.
5. Press the BANK UP or DOWN buttons to switch
between "TL.XX" & "TH.XX". "TL.XX" represents
the Low Byte or Fine channel, generally listed as
the Tilt Fine channel and TH.XX represents the
High Byte or Coarse channel, generally listed as
the Tilt channel. Set it to "TH.XX" and press and
hold down the MODE button and then tap the
SCENE button that corresponds to the Tilt chan-
nel of your fixture. For example, if your fixtures
Tilt channel is 3 then you´d press the SCENE #3
button. Please refer to the fixtures DMX chart. If
your fixtures includes a Tilt Fine channel, press
the Tap/Disp button so the display reads "TL.XX".
Press and hold down the MODE button and then
tap the SCENE button that corresponds to the
Tilt Fine channel of your fixture. For example, if
your fixtures PAn Fine channel is 2 then you´d
press the SCENE #4 button.
6. Press and hold down the Program button and
approximately 2 seconds or until the PROG
indicator in the LED display stops flashing. A
flashing Blackout indicator in the LED display
confirms that the controller is out of Program
mode.
Assign Joystick Reverse
(pan/tilt invert)
1. Press and hold down the Program button for
approximately 2 seconds or until the PROG
indicator in the LED display flashes. Once the
indicator is flashing, record mode is engaged
and you may release the Program button.
2. Press and hold down the MODE button and
then tap the FINE button. The "Assign" and
"Pan" LED's should illuminate.
3. Once again, press and hold down the MODE
button and then tap the FINE button. The "Re-
verse" LED should illuminate.
4. Select the fixtures that you wish to assign the
"Pan Reverse" & "Tilt Reverse" for by pressing
the FIXTURES # buttons, 1-12, so the selected
fixtures LED´s illuminate. Ideally, you should
assign opposite fixtures for Pan/Tilt Reverse.
For example, fixtures 1, 3, 5, 7, etc... should be
assigned normal as described in the previous
section and fixtures 2, 4, 6, etc... should be
assigned reversed so that when moving the joy-
stick around, fixtures movements are reversed
| Tecshow Navigator 3+
English version
P. 5