EDM 08780 Manual De Instrucciones página 16

• Wear dust mask when using the machine. Exposure to the dust
can cause hearing loss.
ES
• Do not touch the moving sanding sheet.
• Do not continue to use worn, torn or heavily clogged sanding
sheets.
PT
• Do not work materials containing asbestos. Asbestos is
considered carcinogenic.
• Secure the work piece (a work piece clamped with clamping
devices or in a vice is held more securely than by hand).
EN
ADDITIONAL SAFETY INSTRUCTIONS FOR BATTERIES AND
CHARGERS
FR
Use only batteries and chargers applicable for this machine.
BATTERIES
• Never attempt to open for any reason.
• Do not store in locations where the temperature may exceed
40 C.
• Charge only at ambient temperatures between 4ºC and 40ºC.
• When disposing of batteries, follow the instructions given in the
section "Protecting the environment".
• Do not cause short circuits. If connection is made between the
positive (+) and negative (-) terminal directly or via accidental
contact with metallic objects, the battery is short circuited and an
intense current will flow causing heat generation which may lead
to casing rupture or fire.
• Do not heat. If batteries are heated to above 100 C, sealing and
insulating separators and other polymer components may be
damaged resulting in electrolyte leakage and/or internal short
circuiting leading to heat generation causing rupture or file.
Moreover do not dispose of the batteries in fire, explosion and/or
intense burning may result.
• Under extreme conditions, battery leakage may occur. When you
notice liquid on the battery, proceed as follows:
• Carefully wipe the liquid off using a cloth. Avoid skin contact.
• In case of skin or eye contact, follow the instructions below:
1. Immediately rinse with water. Neutralize with a mild acid such as
lemon juice or vinegar.
2. In case of eye contact, rinse abundantly with clean water for at
least 10 minutes.
3. Consult a physician.
Fire hazard! Avoid short-circuiting the contacts of a detached
battery. Do not incinerate the battery.
CHARGERS
Instruction manual
OPERATION
Before using the equipment
BATTERY CHARGER
The lithium-ion battery can be charged at any time and will not
develop a "memory" when charged after only a partial discharge. It is
not necessary to run down the battery pack charge before recharging.
Remove the battery pack from the tool when convenient for you and your
job. You can "top-off" your battery pack's charge before starting a big
job or long period of use. Due to lithium-ion's fade-free properties, the
only time it is necessary to charge the lithium-ion battery pack is when
the pack has reached the end of its charge. To signal the end of charge,
power to the tool will drop quickly. Charge the battery pack as needed.
CHARGING THE BATTERY
This lithium-ion battery pack is shipped partially charged. Before using
it the first time, fully charge the battery pack. A fully discharged 2.0Ah
battery pack with a temperature between 4 C and 40 C will charge in
about 1 hour.
Plug the charger adapter into power source. The green light on the
charger stand will illuminate, indicating the charger is powered.
Slide the battery all the way into the charger stand.The red light on the
charger stand will illuminate, indicating that the battery is charging.
The red light will go off after charging is complete and a green light
will appear.
normal. If the battery is hot after continuous use in the tool, allow it to
cool down to room temperature before charging. This will extend the
life of your batteries.
before any assembly, adjustments or changing accessories.
INSERTION AND REMOVAL OF RECHARGEABLE BATTERY
adjustments to the equipment. Be sure to read the following
information before you put the cordless equipment into operation:
Charge the battery pack with the charger. An empty battery pack
• Never attempt to charge non-rechargeable batteries.
• Have defective cords replaced immediately.
• Do not expose to water.
• Do not open the charger.
• Do not probe the charger.
• The charger is intended for indoor use only.
NOTE: Batteries may become warm while charging. This is
WARNING: Always disconnect the battery pack from the tool
• Depress the battery-release button located on the front of the
battery pack to release battery pack. Pull the battery pack out
and remove it from the tool.
WARNING: Always remove the battery pack before making
08780
REF.