Publicidad

Model #
277W
Stafford
Sideboard
Assembly Instructions
Congratulations!
This fine piece of furniture will make a handsome
addition to your home. For the best results, start by
reading both the Assembly Instructions and
Finishing Hints before you begin your project.
For normal household use only.
recommended for commercial use.
Do not climb, sit or stand on this piece of
furniture.
Unload items from this unit prior to moving.
Do not overload shelves on this unit.
Before loading or moving this unit, check all screws
and supports for tightness.
P.O. Box 2827
Eugene, OR 97402 USA
Service Policy:
which are defective, missing or damaged
during assembly. Please contact Whittier
Wood Products customer service department
directly (by phone, fax, mail or email) for
replacement parts.
Hours:
Our friendly customer service staff
can be reached Monday-Friday 7:00 a.m. to
5:00 p.m. (Pacific Time). A message can be
left 24 hours a day, 7 days a week.
To Order:
Provide the complete furniture
model number (upper left corner of this
page), part letter, production code, quantity
needed, reason for replacement and your full
name and address along with a telephone
number in case we need to contact you.
Parts ship from our Eugene, Oregon factory
within 1 or 2 business days from the time
we receive the request. Please allow 5-10
business days for delivery.
Outside U.S. or Canada: 541-687-0213
Outside U.S. or Canada: 541-687-0213
Fax: 541-687-2060 • Email: info@whittierwood.com
Fax: 541-687-2060 • Email: info@whittierwood.com
Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Read both the Assembly Instructions and Finishing
Hints completely before beginning.
Store the parts: 1) in their box; 2) in a dry place; 3) in
temperatures ranging from 40° to 90°. (Not on a cold,
possibly damp, cement floor.)
Inspect your furniture periodically for any loose glue
joints or screws, or any other problem which may
be affecting the stability of your furniture. Tighten or
repair as needed.
Production Code:
We will replace any parts
Rev. 9/05

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Whittier Wood Products 277W

  • Página 1 Model # 277W Stafford Service Policy: We will replace any parts Sideboard which are defective, missing or damaged during assembly. Please contact Whittier Assembly Instructions Wood Products customer service department directly (by phone, fax, mail or email) for replacement parts.
  • Página 2 277W Stafford Sideboard – Parts List BEFORE BEGINNING ASSEMBLY: Check that the quantities of the parts received match those on parts list below. (TOP) (TOP) DESSUS DESSUS PARTE SUPERIOR PARTE SUPERIOR G — Top/Bottom Apron — Qty. 2 FRONT • AVANT • FRENTE HH —...
  • Página 3 277W Stafford Sideboard – Parts List (cont.) W — #8 x 1" Machine Screw P — #6 x 5/8" Philtruss — Qty. 2 Screw — Qty. 18 MP — Door Panel — Qty. 2 (loose in door frames) X — Angle Bracket — Qty. 2 MP –...
  • Página 4: Tools Required

    • two in each Side Panel (AL & AR). Bottom edge of side panels are stamped "L" for left and "R" for right. Glue two Wood Dowels (Q) in each end of both Top/Bottom Aprons (G). READ CAM-LOCK INSTRUCTIONS PAGE 4 — 277W...
  • Página 5 Connectors (N) near the bottom of the side panel and 1/2" Cam Housings (ZE). Glue the Top and Bottom Aprons (G) into the dowel holes in the right front leg. Rounded edges must face forward. Attach the other side panel in the same way. 277W— PAGE 5...
  • Página 6 Attach an Angle Bracket (X) with #6 1/2" Undercut Screw (YY) to the Lower Apron and STAIN TEST AREA bottom of the shelf at each mark. FIG. 6 PAGE 6 — 277W...
  • Página 7 #6 x 3/4" P.O. Zinc Screws (ZZ). See FIGURE 8A. Attach the Knobs (V) to the doors with #8 x 1" Machine Screws (W). See FIGURE 8B. 277W— PAGE 7...
  • Página 8: Side Panel

    The door may need to be adjusted so that all the spaces between the door and the unit sides are equal. Follow instructions in FIGURE 10A. Install the Pads (ZC) to inside of doors where they make contact with the shelf. PAGE 8 — 277W...
  • Página 9 Modelo # 277W Buffette Stafford Normas para obtener servicio: Instrucciones para Armar Reemplaza- remos las piezas que tengan defectos, falten o se dañen durante el armado. Sírvase comunicarse con el departamento de servicio al cliente de Whittier Wood Products directamente (por teléfono, fax, correo o e-mail) para obtener piezas de repuesto.
  • Página 10: Herramientas Necesarias

    Conectores de Leva (N) cerca de la identificado con una “L” para el izquierdo, y una parte inferior del panel lateral y Tuercas de Sujeción “R” para el derecho. Para Leva de 1/2" (ZE). Con pegamento, pegue los 277W — PAGE 2 SP...
  • Página 11 Siga las instrucciones que de estante y dentro del estante. Consulte la FIGURA se presentan en la FIGURA 10A. Instale los almohadilla para puerta (ZC) en el interior de las puertas donde harán contacto con el estante. 277W — PAGE 3 SP...
  • Página 12 No. de modèle 277W Buffet Stafford Politique de service : Nous remplacerons toutes Instructions de Montage les pièces défectueuses, manquantes ou endom- magées pendant le montage. Veuillez contacter directement le service clientèle de Whittier Wood Products (par téléphone, fax, courrier ou e-mail) pour obtenir les pièces de remplacement.
  • Página 13: Outils Nécessaires

    : « L » pour gauche, « R » pour droit. Procédez de la même manière pour fixer l’autre pan- Collez deux tenons en bois (Q) dans chaque extrémité neau latéral. des deux tabliers inférieur/supérieur (G). 277W — PAGE 2 FR...
  • Página 14 8. Posez les encadrements de porte (M1 et M2) face portes, au point de contact avec l’étagère. sur le dessous ; placez ensuite les panneaux de porte (MP) dans les rainures, puis assujettissez-les en place 277W — PAGE 3 FR...

Tabla de contenido