Timer Setting (By Remote Control) - Lenco TCD-974 Manual De Instrucciones

REMOVING OF USB / MEMORY CARD
TO REMOVE THE USB / MEMORY CARD, TURN OFF THE POWER OR SWITCH THE FUNCTION MODE TO
EITHER CD, TAPE OR TUNER FIRST. FOR USB PORT – UN-PLUG IT BY PULLING OUT THE USB SOCKET
DIRECTLY, FOR MEMORY CARD – PRESS THE MEMORY CARD INWARD & THEN RELEASE, NOW THE CARD
BEING PARTIALLY EJECT AND YOU CAN REMOVE IT BY HAND.
PHONO PLAYBACK
NOTED:
- REMOVE THE STYLUS PROTECTOR.
- BE SURE THAT THE TONE ARM IS BEING DETACHED FROM THE TONE ARM
REST BEFORE OPERATING AND RE-SECURED AGAIN AFTERWARDS.
1. SELECT TO "PHONO" FUNCTION BY FUNCTION BUTTON (4).
2. SET THE SPEED SELECTOR TO THE PROPER POSITION DEPENDING ON THE RECORD TO BE PLAYED.
3. PLACE THE RECORD ON THE PLATTER (USE THE SPINDLE ADAPTOR IF REQUIRED).
4.
LIFT THE TONE ARM FROM THE REST AND SLOWLY MOVE IT TO THE RECORD SIDE. THE
PLATTERWILLSTART TO ROTATE
5. PLACE THE TONE ARM TO THE DESIRED POSITION OF THE RECORD.
6. ADJUST THE VOLUME TO THE DESIRED LEVEL.
7. AT THE END OF RECORD, THE PLATTER WILL AUTOMATICALLY STOP ROTATING.
LIFT THE TONE ARM FROM THE RECORD AND RETURN IT TO THE REST.
8. TO STOP MANUALLY, LIFT THE TONE ARM FROM THE RECORD AND RETURN IT TO
THE REST.
REMARK: AS SOME KIND OF RECORD THE AUTO-STOP AREA WAS OUT OF THE UNIT SETTING, SO IT WILL
STOP BEFORE THE LAST TRACK FINISH. IN THIS CASE, SELECT THE AUTO-STOP SWITCH (22)TO " OFF
" POSITION, THEN IT WILL RUN TO THE END OF THE RECORD BUT WILL NOT STOP AUTOMATICALLY (TURN
OFF THE UNIT BY POWER BUTTON OR SWITCH BACK THE AUTO-STOP SWITCH (22) TO " ON " POSITION TO
STOP THE PLATTER ROTATE). THEN PUT BACK THE TONE ARM TO THE REST POSITION.
MORE FEATURES
A. SLEEP SETTING (BY REMOTE CONTROL)
1. PRESS "SLEEP" BUTTON AND "SLEEP" INDICATOR WILL SHOWN ON THE LCD DISPLAY (2).
2. KEEP PRESSING THE BUTTON TO ADJUST THE SLEEP TIMER IN THE ORDER OF 90..80.. 70 ...10MINUTES.
3. SYSTEM WILL STOP AND GOTO STANDBY MODE AUTOMATICALLY AFTER THE SELECTED TIMING.
4. TO CANCEL THE SLEEP MODE, PRESS "SLEEP" BUTTON UNIT IT REACHS "OFF" MODE.
REMARK:-
IF PRESS THE SLEEP BUTTON ONCE AND THE "SLEEP" INDICATORAPPEAR ON THE LCD DISPLAY (2), THE
SYSTEM WILL GOTO STANDBY MODE AUTOMATICALLY AFTER SELECTED MINUTES.
B. TIMER SETTING (BY REMOTE CONTROL)
THIS FUNCTION ALLOWS THE SYSTEM TO TURN ON AUTOMATICALLY AND WAKE YOU UP BY CD, TUNER,
USB OR SD MODE RESPECTIVELY.
FIRST, SET THE UNIT AT STANDBY MODE AND THEN PRESS & HOLD THE "TIMER" BUTTON. THE LCD
DISPLAY WILL SHOW "SET TIMER SELECT SOURCE", PRESS FUNCTION BUTTON TO SELECT SOURCE,
PRESS TIMER BUTTON AGAIN TO ENTER THE TIMER SETTING MODE.
1) WAKE UP SOURCE:
2) WAKE UP TIME:
IF THERE IS NO MUSIC SOURCE BEING DETECTED (SUCH AS USB/SD/CD) WHEN THE PRESET TIME IS

REACHED, SYSTEM WILL DEFAULT TO TUNER MODE AUTOMATICALLY.
FOR TUNER WAKE UP, THE SYSTEM WILL PRESET AT THE LATEST RADIO FRQUENCY BEING LISTENED

BEFORE SWITCHING OFF.
SWITCH OFF THE TIMER FUNCTION MANUALLY BY PRESS POWER ON/STANDBY BUTTON (5).

PRESS THE "FUNCTION " BUTTON TO SELECT THE SOURCE FROM " TUNER
"–"CD"-"USB " - " SD " REPEATLY. PRESS " TIMER " BUTTON AGAIN AFTER
SELECTED THE SOURCE.
PRESS SKIP UP / DOWN
TIMER BUTTON TO STORE THE WAKE UP HOUR. PRESS SKIP UP
" BUTTON TO SET& MINUTES AND PRESS " TIMER " BUTTON " TO STORE THE
TIMER ON TIME.TIMER ICON "
"BUTTON TO SET THE HOUR THEN PRESS
" WILL APPEAR ON THE DISPLAY.
GB- 7
/ DOWN