Chicco TRIO LOVE Instrucciones De Uso página 15

REMOVING THE CARRY COT LINING
Before starting to remove the carry cot lining, unfasten the
safety harness (see the paragraph USING THE CARRY COT
13. To remove the hood, unfasten the buttons on the sides
and pull out the fabric from the pin in the rear part of
the carry cot; Then pull out the hinges from their slots
(fig. 13A – 13B).
14. Release the elastic straps from the hood's pin joints (fig.
14A), remove the plastic positioned on the carrycot's
sides (fig. 14B). Unfasten the buttons on the sides of the
it slide under the carry cot's structure (fig. 14E). Remove
the internal lining by pulling it up (fig. 14F). To remove
completely the carrycot's lining, remove the safety har-
ness devices from their slots located at the base of the
internal lining (fig. 14G).
REPLACING THE CARRYCOT LINING
15. Insert the shoulder straps and the crotch strap into the
fabric lining's holes (fig. 15A); Insert the plastic into the
slot between the styrofoam protections and the car-
rycot structure (fig. 15B). Fit the front part of the fabric
Repeat this step on the opposite side of the carrycot
in the relevant openings (fig. 15E) and pass the elastic
straps around the pin joints of the hood (fig. 15F). Fit the
side the relevant slots. To complete replacing the lining,
fasten the hood and cover as described above.
CARRY COT SAFETY HARNESS
The carry cot features a three-point safety harness com-
posed of two shoulder straps and a crotch strap.
WARNING: The safety harness must be used solely to
transport the child in the car.
16. For all other use, put the safety harness under the mat-
tress in the relevant space as illustrated in fig. 16A and
16B.
17. To position the shoulder straps in their slots, loosen
them by means of the button located near the position
USING THE CARRY COT SAFETY HARNESS
the red button and spread the straps (fig. 18A – 18B).
ton located on the outside of the carry cot near the po-
20. Now you can put your child inside the carry out and run
the upper straps over your child's shoulders. Overlap the
ing fastening (fig. 20B).
WARNING:
WARNING:
harness is fastened correctly, pull it with force.
21. Tighten the safety harness of the carry out by pulling on
the relevant adjustment belt (fig. 21).
WARNING: to use the carry cot in the car, the carrying han-
USING THE CARRY COT IN THE CAR
Read these instructions carefully before fitting and install-
ing the product. Prevent anybody to use the product with-
out reading the instructions.
your baby in the event of a crash; however, use of this
injury to your baby, not only in case of a crash, but also in
other situations as well.
replaced: as its original safety features may have been
compromised.
modification is approved by the manufacturer. Do not in-
stall accessories, spare parts, or any component not sup-
plied by the manufacturer.
none of its parts are too hot: in such an event, let the child
car seat cool down first before placing the child into it, in
order to avoid burns.
- KIT may have been damaged, even if it is not visible to the
fered structural damage, even if this is not visible to the
of its product.
WARNING
to Regulation No. 44.04 series of amendments 04. Suitable
for general use in vehicles and compatible with most but
not all vehicles' seats.
your vehicle has indicated in the car manual whether your
vehicle foresees the installation of Universal child retention
devices for the age group in object.
more stringent conditions than those that were applied to
- earlier designs not displaying this notice.
3-point retractor safety belts approved according to UN/
ECE Regulation No.16, or other equivalent standard.
device or reseller.
-
CAR SEAT REQUIREMENTS
22. To fasten the carry cot to the car seat, the car seat must
meet the following requirements:
- it must be facing forward (fig. 22A);
- it must be a rear seat with at least two 3-point seat belts
(fig. 22B), approved according to standard UNI/ECE 16 or
other equivalent standard.
15
-
-