Refrigerator Care - KitchenAid T2WG2 Manual De Uso Y Cuidado

Refrigerador de dos puertas con profundidad de mostrador
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

2. Replace thestorage binonthedoor a ndpush down tomake
sure itissecurely inplace.
NOTE: Do not use with water that is microbiologically
unsafe
or of unknown quality without
adequate
disinfection
before or
after the system.
Water
Filter Status Display
(on some models)
The filter status display will help you know when to change your
water filter. When the display reads 10%, order a new filter. It is
recommended
that you replace the filter when the display reads
0% OR when water flow to your water dispenser or ice maker
decreases noticeably.
After changing the filter, reset the display by pressing the button.
The display will read 99% when the system is reset.
Non-indicator
Water Filter (on some models)
If your refrigerator does not have the status light, you should
change the water filter every 6 months depending upon your
usage. If the water flow to the water dispenser or ice maker
decreases noticeably before 6 months have passed, replace the
water filter more often.
Changing
the Water Filter
1. Press the eject button to release the filter from the base grille•
2. Pull the filter straight out.
3. Turn the cap counterclockwise
to remove it from the filter.
IMPORTANT: Do not discard the cap. It is part of your
refrigerator. Keep the cap to use with the replacement filter.
4. Align the ridge on the cap with the arrow on the new filter and
turn the cap until it snaps into place.
NOTE: You can run the ice maker without a filter. Your water
will not be filtered. Simply insert the cap all of the way into the
base grille and rotate the cap until it is firmly in place.
5. Remove the protective covers from the O-rings. Be sure the
O-rings are still in place after the covers are removed.
6. Push the filter into the base grille. The eject button will pop
back out when the filter is fully engaged.
REFRIGERATOR CARE
Explosion
Hazard
Use nonflammable
cleaner.
Failure to do so can result in death, explosion, or fire.
Both the refrigerator and freezer sections defrost automatically.
However, clean both sections about once a month to prevent
odors from building up, Wipe up spills immediately.
IMPORTANT: Because air circulates between both sections, any
odors formed in one section will transfer to the other• You must
thoroughly clean both sections to eliminate odors• To prevent
odor transfer and drying out of food, wrap or cover foods tightly.
To Clean Your Refrigerator:
NOTE: Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, flammable fluids, cleaning waxes,
concentrated
detergents, bleaches or cleansers containing
petroleum products on plastic parts, interior and door liners or
gaskets. Do not use paper towels, scouring pads, or other harsh
cleaning tools.
1. Unplug refrigerator or disconnect power.
2. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.
3.
4.
Wash stainless steel and painted metal exteriors with a clean
sponge or soft cloth and a mild detergent in warm water•
There is no need for routine condenser cleaning in normal
home operating environments• If the environment is
particularly greasy or dusty, or there is significant pet traffic in
the home, the condenser should be cleaned every 2 to
3 months to ensure maximum efficiency.
If you need to clean the condenser:
Removethe
base grille.
Use a vacuum cleaner with a soft brush to clean the grille,
the open areas behind the grille and the front surface area
of the condenser•
Replace the base grille when finished.
Plug in refrigerator or reconnect power•
NOTE: Not all bulbs will fit your refrigerator. Be sure to replace the
bulb with one of the same size, shape and wattage. On some
models, the dispenser light requires a heavy duty 10-watt bulb. All
other lights require a 40-watt bulb. Replacement bulbs are
available from your dealer.
1. Unplug refrigerator or disconnect power.
2. Remove light shield when applicable.
NOTE: To clean the light shield, wash it with warm water and
liquid detergent. Rinse and dry the shield well.
3. Remove light bulb and replace with one of the same size,
shape and wattage.
4. Replace light shield when applicable.
5. Plug in refrigerator or reconnect power.

Publicidad

Tabla de contenido

Solución de problemas

loading

Este manual también es adecuado para:

T2wg2lT1wg2T1wg2l

Tabla de contenido