General Safety Rules; Personal Safety; General Power Tool Safety Warnings; Work Area Safety - Hilti ST1800 Manual De Instrucciones

2. General safety rules

NOTE
The safety rules in section 2.1 contain all general
safety rules for power tools which, in accordance
with the applicable standards, require to be listed in
en
the operating instructions. Accordingly, some of the
rules listed may not be relevant to this tool.

2.1 General Power Tool Safety Warnings

a) WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire
and/or serious injury. Save all warnings and
instructions for future reference. The term "power
tool" in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless)
power tool.

2.1.1 Work area safety

a) Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b) Do not operate power tools in explosive atmos-
pheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to
lose control.

2.1.2 Electrical safety

a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
b) Avoid body contact with earthed or grounded sur-
faces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk
of electric shock.
2
Printed: 07.07.2013 | Doc-Nr: PUB / 5070704 / 000 / 00
All manuals and user guides at all-guides.com

2.1.3 Personal safety

a) Stay alert, watch what you are doing and use
b) Use personal protective equipment. Always wear
c) Prevent unintentional starting. Ensure the switch
d) Remove any adjusting key or wrench before turn-
e) Do not overreach. Keep proper footing and bal-
f) Dress properly. Do not wear loose clothing or
g) If devices are provided for the connection of dust
2.1.4 Power tool use and care
a) Do not force the power tool. Use the correct pow-
b) Do not use the power tool if the switch does not
c) Disconnect the plug from the power source
d) Store idle power tools out of the reach of chil-
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will
reduce personal injuries.
is in the off-position before connecting to power
source and/or battery pack, picking up or carry-
ing the tool. Carrying power tools with your finger
on the switch or energising power tools that have
the switch on invites accidents.
ing the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
ance at all times. This enables better control of
the power tool in unexpected situations.
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
extraction and collection facilities, ensure these
are connected and properly used. Use of dust col-
lection can reduce dust-related hazards.
er tool for your application. The correct power
tool will do the job better and safer at the rate for
which it was designed.
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
and/or the battery pack from the power tool
before making any adjustments, changing acces-
sories, or storing power tools. Such preventive
safety measures reduce the risk of starting the
power tool accidentally.
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.