Festool MFT/3 Manual De Instrucciones Original página 11

To attach the guide rail, place on the key [3-3]
and make sure that the end of the rail is resting
on the support plate and the key is located cor-
rectly in the groove.
Secure the guide rail in this position with the
two screws [3-4] and tighten using the hexagon
wrench.
5.3 Defl ector
The defl ector [1-9] prevents the extraction hose
and the power cable from catching on the guide
rail. The defl ector is attached to the end of the
guide rail and secured with the rotary knob [1-
10].
5.4 Attaching the pre-set profi le setting rail
The rail can be attached at any point along the
clamping edge of the bench and is so versatile,
it can be used as a cross stop or a longitudinal
stop.
L
Before attaching, make sure that the V groove
on the fence is not dirty.
f
Open the clamping jaws using the knob
f
Place the fence with guide rail
clamp rail from above.
f
Secure the clamp segment using the knob
The additional clamp [1-7] is designed to secure
the stop ruler.
f
Guide the additional clamp into the V groove
on the MFT/3 and the guide slot on the stop
ruler.
f
Secure the additional clamp using the clamp
lever and the rotary knob.
5.5 Mounting the KAPEX
The perforated top on the MFT/KAPEX was spe-
cially designed for mounting the KAPEX KS 120/
KS 88.
f
Mount the machine on the MFT/KAPEX as
shown in Fig.[6].
f
Secure the machine to the MFT using clamps.
WARNING
Risk of injury
f
Before starting work, make sure that the ma-
chine is secured properly
f
Respect the maximum workpiece dimen-
sions.
6 Working with the MFT
L
The multifunction table offers a wide range
of application options! To fi nd out more about
possible machine applications, order the
MFT application manual on the internet.
6.1
Check the angle setting of the pre-set profi le
setting rail before starting work. Align the guide
rail fi rst of all [7a].
f
f
f
L
If required, the pre-set profi le setting rail can
also be aligned in relation to the perforated top
provided the necessary clamps (accessories) are
available.
f
If the stop ruler does not rest evenly against the
[5-4]. clamps:
f
[5-5] onto the
[5-4] .
f
The fence can be adjusted in the following ways:
Adjustment parallel to the bench edge:
f
f
Adjustment at right angles to the bench edge:
f
f
Adjusting the stop ruler [5-6] lengthways
f
Angle adjustment using the scale
f
Risk of injury
f
f
Adjusting the pre-set profi le setting rail
Align the guide rail at right angles to the pre-
set profi le setting rail.
If an angle of 90° is not possible, slide a sup-
port unit on the guide rail until the angle is
correct.
Secure the guide rail.
Slide the relevant stop
ble profi le to retain the setting permanently.
Insert the clamps [7-1] and [7-2] as shown in
Fig. [7b] and move the stop ruler [7-3] to a 90°
position.
Loosen the screws
[5-2]. The retaining pin must be engaged in the
90° notch.
Set the angle at 90° in relation to the clamps
and tighten the screws.
Loosen the rotary knob
Slide the stop into the groove on the MFT/3.
Loosen the rotary knob
Slide the stop into the groove on the MFT/3.
Loosen the rotary knob
can be moved to a lower position for thin work-
pieces or a higher position for thicker work-
pieces.
Loosen the rotary knob
ing pin [5-3]. The rotary retaining pin engages
in the most common angle positions.
WARNING
Always use the fence in a fi xed position and do
not use to slide the workpiece along!
Make sure that all rotary knobs on the fence
are tightened before starting work.
[3-1/4-4] along the ta-
[7-4] and the rotary knob
[5-4].
[5-4].
[5-1]. The stop ruler
[5-2] and lift the retain-
11