Assembly And Adjustments - DeWalt D28065 Traducido De Las Instrucciones Originales

Ocultar thumbs Ver también para D28065:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 43
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
D
WALT service organization.
E
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in
the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor
size is 1 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.
Attaching Side Handle
WARNING: Before using the tool,
check that the handle is tightened
securely.
Screw the side handle (g) tightly into one of the holes
(h) on either side of the gear case.
Mounting and Removing the Guard
(fi g. 2)
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.
CAUTION: Guards must be used with
this grinder.
When using the D28065 grinder for cutting metal
or masonry a Type 1 guard MUST be used. Type
1 guards are available at extra cost from D
distributors.
NOTE: Please refer to the Grinding and Cutting
Accessory Chart at the end of this section to
show other accessories that can be used with these
grinders.
1. Place the angle grinder on a table, spindle up.
2. Release the clamping lock (l) and hold the guard
(e) over the tool as shown.
3. Align the lugs (m) with the notches (n).
4. Press the guard down and rotate it to the
required position.
5. If required, increase the clamping force by
tightening the screw (o).
6. Tighten the clamping lock (l) .
7. To remove the guard, release the clamping lock
CAUTION: If the guard cannot be
tightened by the adjusting screw, do
not use the tool. To reduce the risk of
personal injury, take the tool and guard
to a service center to repair or replace
the guard.
NOTICE: To reduce the risk of damage
to the tool, do not tighten the adjusting
screw with the clamp lever in the open
position. Undetectable damage to the
guard or the mounting hub may result.
Fitting and Removing a Grinding or
Cutting Disc (fi g. 1, 4, 5)
WARNING: Do not use a damaged
disc.
1. Place the tool on a table, guard up.
2. Fit the backing flange (j) correctly onto the
spindle (q) (fig. 4).
3. Place the disc (p) on the backing flange (j).
When fitting a disc with a raised center, make
sure that the raised centre (k) is facing the
backing flange (j).
4. Screw the threaded clamp nut (i) onto the
spindle (q) (fig. 5):
EN GL IS H
WALT
E
35

Publicidad

Tabla de contenido
loading

Tabla de contenido