Facom Y_116C Traducido De Las Instrucciones Originales página 11

• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS
Setting the Adjustable Head (Fig. B)
For best results it is important to adjust the head of the rivit
pliers to match the rivet size for your application.
nOTE: Factory setting is for 1/4" (6.4 mm) rivets.
1. If you want to use 3/16" (4.8 mm) rivets, use the nose piece
wrench 9 to remove the nose piece on the adjustable head
2. Then rotate the adjustable head
use 3/16" (4.8mm) or smaller rivets. Install appropriate nose
piece onto the adjustable head.
3. Rotate the adjustable head
factory setting of 1/4" (6.4 mm) rivets.Install appropriate
nose piece onto the adjustable head.
Replacing Nose Pieces (Fig. A, C)
1. Select appropriate sized nose piece
desired size rivet for your application.
2. Hold the adjustable head with one hand, use the other
hand to turn the nose piece counterclockwise wtih the nose
piece wrench 9 . Remove the installed nose piece from the
adjustable head 2 of the rivet pliers.
3. Start to thread the desired nose piece onto the adjustable
head 2 of the rivet plier.
4. Use the nose piece wrench
clockwise until tight.
5. Keep nose pieces not in use stored safely in the four
nose piece storage holes
handles 1 .
nOTE: Nose pieces are removed from storage by rotating
the nose piece counterclockwise and installed in the storage
holes by rotating the nose piece clockwise until tight.
OPERATION

CAUTION: Wear safety glasses and gloves
during operation.
Proper Hand Position (Fig. A)

WARNING: To avoid risk of serious injury, ensure both
hands are on the handle grips during operation.

WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires both hands on the handle grips
Nose Piece Size Reference Chart
RIVET
MATERIAL
3/32"
(2.4mm)
Aluminum X
Steel X
2 180 ° anticlockwise to
2 180 ° clockwise to use the
4 , 5 , 6 , 7 for the
9 , and turn the nose piece
8 located on either side of the
NOSE PIECE SIZE
1/8" 5/32" 3/16"
(3.2mm) (4.0mm) (4.8mm)
X X X
X X X
Stainless Steel
Rivet Application (Fig. A. —E)
1. Select correct rivet length for your application.
2. Ensure the nose piece
the rivet 11
3. Drill a hole that matches the rivet thickness through the
materials you intend to rivet.
4. Insert the rivet pin
ensure the rivet head
5. With handles
into the nose piece.
2 .
6. Ensure rivet pliers
as shown in Fig. E.
7. Squeeze the handles
install the rivet to the workpeice.
8. The clipped rivet mandrel
storage cup
9. To empty the mandrel storage cup
pliers and dispose of rivet mandrels in an appropriate dust bin.
10. Screw the mandrel storage cup onto the pliers until snug.
MAINTENANCE
Your FACOM hand tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
C
Lubrication
Your tool requires no additional lubrication.
D
Cleaning

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories

WARNING: Since accessories, other than those offered
by FACOM, have not been tested with this product, use
.
1
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only FACOM recommended
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
1/4"
(6.4mm)
X
X X X
3 , 4 , 5 , 6 , 7
you are operating with.
12 into the hole of the workpeice and
13 is flush with the workpeice.
1 in the open postion, place rivet mandrel
14 are perpendicular with the workpeice
1 together to the closed position to
15 falls into the mandrel
10 .
10 , unscrew from the
EngLIsh
matches the size of
15
9