Thomashilfen RECARO Monza Nova 2 Reha Instrucciones De Montaje página 8

RECARO Monza Nova 2 Reha – Instructions for assembly and use (supplement)
Purpose / indication
The children car seat RECARO Monza Nova 2 Reha / Monza Nova 2 Seatfix Reha is designed for the transport of children with special needs in vehicles. The clinical
pictures are amongst others:
• cerebral palsy
• hypotony syndrome of unspecific genesis
• muscular dystrophy
• different syndrome diseases
The car seat is characterized by its shell design and pad system, which provide for additional seating safety, stabilization of head and pelvis, and support/control of the feet.
Thus, the RECARO Monza Nova 2 Reha / Monza Nova 2 Seatfix Reha meets the needs of disabled children very well.
Application risks / contraindications
No application risks / contraindications are known.
5-point positioning belt
Please note: The 5-point positioning belt helps positioning the child in the car seat and does not protect the child in the event of an accident. The 3-point belt in the car
must always be used to secure the child in the seat. Do not route the 5-point belt through the red belt guides on the headrest. They are intended only for the 3-point
belt.
Adjusting the belt length:
Pull the loose belt straps to shorten and tighten the belts. To lengthen the belts, press the release mechanism on the adjustment buckle and then pull out the belt to the
desired length.
If required, the belt length can also be adjusted with the two belt loops (bolted) at the back of the seat.
Belt buckle:
Press the red dent of the buckle to open. Separate the two upper belt fasteners. To close the belt, put the belt fasteners into the buckle and push together until they lock in
place with an audible „Click".
The cover for the crotch pad (zipper) can be removed and washed in the machine at up to 30° C / 86° F. Please undo the zip on the bottom crotch pad as well to remove
the cover.
Fig. 1a: Adjusting the belt length
Headrest
Adjust the seat's headrest to the highest position to facilitate attaching the headrest. Pull the covers of the supports over the side parts of the headrest and fasten them at
the top with the press button. The pads are fastened to the lower part of the headrest with an elastic rubber band.
The cover can be removed (zipper) and washed in the machine at up to 30° C / 86° F.
Fig. 2a: Attaching the headrest
Lateral trunk supports
The lateral trunk supports can be fastened at 3 different heights on the left and right in the back area with press buttons and Velcro. Start with the press buttons.
The supports can be fixed more firmly by pressing against the fleece strips in the back of the seat.
The cover can be removed (zipper) and washed in the machine at up to 30° C / 86° F.
Fig. 3a: Press button
Lateral seat supports
Adjust the backrest to a horizontal position to facilitate attachment of the lateral supports. Pull the covers of the lateral supports over the side parts of the seat surface and
attach them to the rear of the seat surface with the press button.
The cover can be removed (zipper) and washed in the machine at up to 30° C / 86° F.
Fig. 4a: Attaching the support
Abduction block
The abduction block can be adjusted in depth. In order to do so, it first has to be released from the groin belt. Remove the belt strap end piece from the end of the groin
belt and unthread the belt from the sliding buckle and belt buckle. Pull the abduction block up and off the groin belt.
Thread the groin belt back through the sliding buckle and belt buckle, and secure the loose end of the belt with the belt end piece. Position the abduction block as
needed on the hook-and-loop fastener provided on the seat bottom.
The cover is removable (zipper) and machine washable at up to 30°C. To remove the cover, the abduction block first has to be released from the groin belt as described
above.
Fig. 5a: Belt end piece
Fig. 5c: Unthreading the sliding buckle and belt buckle
Swivel base with footrest adapter (accessory)
Please note our separate instructions for mounting! Download: www.thomashilfen.com
Seatfix connection (for swivel base) (accessory)
Please note our separate instructions for mounting! Download: www.thomashilfen.com
8
Fig. 1b: Opening and closing the belt buckle („Click")
Fig. 2b: Fastening at bottom
Fig. 3b: Velcro-fastening
Fig. 4b: Press button, rear
Fig. 2c: Fastening at top
Fig. 5b: Removing the belt end piece
Fig. 5d: Removing the abduction block
item code: 820/1
item code: 818