Tabla de contenido
Publicidad
• Lower guard should be retracted manually only for
special cuts such as plunge cuts and compound
cuts; raise lower guard by retracting handle and as
soon as blade enters the material, the lower guard
must be released (for all other sawing, the lower guard
should operate automatically)
• Always observe that the lower guard is covering the
blade before placing saw down on bench or floor (an
unprotected, coasting blade will cause the saw to walk
backwards, cutting whatever is in its path; be aware of
the time it takes for the blade to stop after switch is
released)
GENERAL
• Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
• Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
• Use suitable detectors to find hidden utility lines or
call the local utility company for assistance (contact
with electric lines can lead to fi re or electrical shock;
damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or
an electrical shock)
• When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
• Use completely unrolled and safe extension cords with
a capacity of 16 Amps (U.K. 13 Amps)
• In case of jamming or electrical or mechanical
malfunction, immediately switch off the tool and
disconnect the plug
• SKIL can assure fl awless functioning of the tool only
when the correct accessories are used which can be
obtained from your SKIL dealer
• Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
• Never use the tool without the original protection guard
system
• This tool should not be used by people under the age of
16 years
• The noise level when working can exceed 85 dB(A);
wear ear protection
• If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
• Never use the tool when cord is damaged; have it
replaced by a qualifi ed person
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools
with a rating of 230V or 240V can also be connected to
a 220V supply)
• Starting cycles generate brief voltage drops;
interference with other equipment/machines may occur
in case of unfavourable mains system conditions
(malfunctions are not to be expected for system
impedances below 0.36 ohm) - if you need further
clarifi cation, you may contact your local power supply
authority
All manuals and user guides at all-guides.com
• This tool is not suitable for wet cutting
• After switching off your circular saw, never stop the
• Never use circular saw blades made of high speed steel
• Never use grinding/cutting discs with this tool
• Do not work materials containing asbestos (asbestos
• Dust from material such as paint containing lead, some
• Certain kinds of dust are classifi ed as carcinogenic
• Follow the dust-related national requirements for the
• Do not attempt to cut extremely small workpieces
• Remove all obstacles on top of as well as underneath
• Do not work overhead with the tool
• Only use a saw table provided with a switch that
• Only use a saw table provided with a kerf guide
• Always disconnect plug from power source before
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
• If for any reason the old plug is cut off the cord of this
USE
• Mounting saw blade 3
9
rotation of the saw blade by a lateral force applied
against it
(HSS)
is considered carcinogenic)
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause
allergic reactions and/or respiratory diseases to the
operator or bystanders); wear a dust mask and work
with a dust extraction device when connectable
(such as oak and beech dust) especially in conjunction
with additives for wood conditioning; wear a dust
mask and work with a dust extraction device when
connectable
materials you want to work with
the cutting path before you start cutting
prevents restarting of the motor after interruption of
voltage
making any adjustment or changing any accessory
in the cord of this tool to the earth terminal of the plug
tool, it must be disposed of safely and not left
unattended
! disconnect the plug
- take hex key A from storage B
- push spindle-lock button C and hold it while you
remove blade bolt D with blade wrench
! push spindle-lock button C only when tool is at a
standstill
- release spindle-lock button C
- remove fl ange E
- open lower guard F with lever G and hold it while you
mount saw blade with saw teeth and arrow printed
on saw blade pointing in same direction as arrow on
lower guard
- release lower guard F
- mount fl ange E
! make sure that clamping surfaces H of flanges
are perfectly clean and face the blade
Publicidad
Tabla de contenido
