Technical Data; Cleaning And Maintenance - EINHELL Power-X-Boostcharger 6A Manual De Instrucciones Original

2. Layout (Fig. 1)
1. Charger
2. Charging cable
3. Boost button

3. Technical data

Charger
Input ........................ 220-240V~50-60Hz, 150 W
Output (normal) .............................. 18 V d.c., 3A
Output (boost) ................................ 18 V d.c., 6A
Caution!
The charging unit is allowed to be used only for
the lithium-ion batteries of the Power-X-Change
series!
Power-X-Change
•
18 V, 1.5 Ah, 5 lithium-ion cells
•
18 V, 2.0 Ah, 5 lithium-ion cells
•
18 V, 3.0 Ah, 10 lithium-ion cells
•
18 V, 4.0 Ah, 10 lithium-ion cells
Power X-Change Plus
•
18 V, 2.6 Ah, 5 lithium-ion cells
•
18 V, 5.2 Ah, 10 lithium-ion cells
4. Operation (Fig. 1-3)
1. Pull the battery pack (a) out of the handle,
pressing the pushlock button (b) as you do
so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(1) into the socket outlet. The green LED will
then begin to fl ash.
3. Insert the battery pack (a) into the battery
charger (1).
4. In section 7 „Charger indicator" you will fi nd a
table with an explanation of the LED indicator
on the charger.
5. Boost charging
In boost charging mode the rechargeable bat-
tery is charged more quickly than in normal
high-speed charging mode. Press the boost
button (3) to switch to boost charging mode.
This is indicated by the blue LED. (see point
7)
Anl_Power_X_Boostcharger_6A_SKP9.indb 15 Anl_Power_X_Boostcharger_6A_SKP9.indb 15
GB
Important!
Boost charging is recommended when the battery
needs to be got ready for work again quickly.
If the battery is not required again quickly after
use, recharge it in normal high-speed charging
mode, because this mode of charging places less
stress on the lithium-ion battery.
If the battery fails to charge, please check
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts of the charging unit
If the battery still fails to charge, send
•
the charging unit
•
and the rechargeable battery
to our customer service center.
Customer service:
ISC GmbH International Service Center
Eschenstrasse 6, 94405 Landau/Isar, Germany
www.isc-gmbh.info
Timely recharging of the battery will help it serve
you well for a long time. You must recharge the
battery when you notice that the power of the
cordless screwdriver drops.
Mounting the charging unit on a wall (Fig. 4)
The charging unit can also be mounted on a wall.
The correct dimensions for drilling holes in the
wall can be found on the back of the charging unit.
Spacing distances
≥ 10 cm from the wall (right + left)
≥ 100 cm from the ceiling
Caution!
When mounting on a wall you must use suitable
screws, e.g. 3.5 mm pan-head screws, in order to
prevent damage to the housing and risk of falling.

5. Cleaning and maintenance

Always pull out the power plug before starting any
cleaning work.
The equipment is not allowed to be stored in a
damp location or where there are caustic gases.
Keep it in a dry place out of the reach of children.
- 15 -
05.01.2018 11:30:18 05.01.2018 11:30:18