Technics SU-R1A Instrucciones De Funcionamiento página 25

Remote control
The remote control does not work properly.
≥ To avoid interference, please do not put any objects in front
of signal sensor. ( 7)
≥ Change the remote control code if other products react to
this remote control. ( 22)
Messages
The following messages or service numbers may appear
on the unit's display.
"AUTO OFF"
≥ The unit has been left unused for about 20 minutes and will enter
standby mode within a minute. Press any button to cancel it.
"Checking Connection"
≥ The unit is checking the connected iPhone/iPad/iPod or a
USB device.
"Download Error"
≥ The firmware download has failed. Press any button to exit.
Please try again later.
≥ The server cannot be found. Press any button to exit. Make
sure that the network is connected to the Internet.
"Empty"
≥ The selected folder is empty. Move tracks into the folder
and retry the operation.
≥ The server is not found on the network. Check to see if the
server is connected to the same network as this unit, and
retry the connection to this unit. (
"Error"
≥ Incorrect operation is performed. Read the instructions and
try again.
"Firmware update is available"
≥ "Firmware updates" ( 22)
"F " (" " stands for a number.)
≥ There is a problem with this unit.
– Is the volume extremely high?
If so, lower the volume.
– Is this unit placed in an extremely hot place?
If so, move this unit to a cooler place and wait a few moments
and then try to turn it on again.
If the problem persists, write down the displayed number,
disconnect the AC mains lead and consult your dealer.
"No Network Connection"
≥ This unit is not connected to the network.
Check the network connection. (
15)
14)
"Not Conditional"
≥ The function you have tried to use is not available with the
current settings. Check the steps and settings.
"Over Flow"
≥ The audio from the analogue audio input terminal in use is
distorted. Select "Attenuator", and change the setting for
the analogue audio input terminal in use to "On". (
"PGM Full"
≥ The number of programmed tracks is more than 24.
"Please Wait"
≥ This is displayed, for example, when this unit is turned
on/off. (For up to 1 minute and 30 seconds)
"Remote " (" " stands for a number.)
≥ The remote control and this unit are using different codes.
Change the code on the remote control.
– When "Remote 1" is displayed, press and hold [OK] and [1] for
at least 4 seconds.
– When "Remote 2" is displayed, press and hold [OK] and [2] for
at least 4 seconds.
"Searching"
≥ The unit is checking the DLNA server on the network.
"Unlocked"
≥ "PC", "AES", "COAX1", "COAX2", "COAX3" or "OPT" is
selected, but no device is connected. Check the
connection with the device. (
≥ Audio signals, such as sampling frequency components,
are not input correctly.
– About supported format, refer to "File format" (
"USB Over Current Error"
≥ The iPhone/iPad/iPod or USB device is drawing too much
power. Disconnect the iPhone/iPad/iPod or USB device
and turn the unit off and on again.
"Hub Device Not Supported"
"Unrecognizable Device"
"Unsupported"
"Unsupported USB Device"
≥ You have connected an iPhone/iPad/iPod or USB device
that is not supported.
– If the iPhone/iPad/iPod is compatible, turn it on and connect it
correctly.
≥ The format of the file on the iPhone/iPad/iPod or USB
device is not supported.
– About supported format, refer to "File format" (
20)
10, 11)
28)
28)
(25)
25