Robust RB-RH 1600 Manual De Instrucciones Original página 14

Anleitung_RB_RH_1600_SPK7__ 10.07.14 09:39 Seite 14
GB
correctly attached and correctly used. The
use of a dust extraction system can reduce the
danger posed by dust.
4. Usage and treatment of the electric tool
a) Do not overload the appliance. Use the
correct tool for your work. You will be able to
work better and more safely within the given
performance boundaries.
b) Do not use an electric tool with a defective
switch. An electric tool that cannot be switched
on or off is dangerous and must be repaired.
c) Pull the plug out of the socket and/or remove
the battery before making any adjustments to
the appliance, changing accessories or put
the appliance down. This safety measure
prevents starting the electric tool unintentionally.
d) Keep unused electric tools out of the reach
of children. Do not allow people who are not
familiar with the appliance or who have not
read these instructions to use the appliance.
Electric tools are dangerous if they are used by
inexperienced people.
e) Clean your electric tool carefully. Check
whether moving parts are functioning
properly and not jamming, whether parts are
broken or damaged enough that the
functioning of this electric tool is affected.
Have damaged parts repaired before using
the appliance. Many accidents are caused by
badly maintained electric tools.
f) Keep your cutting tools sharp and clean.
Carefully maintained cutting tools with sharp
cutting edges will jam less and are easier to
control.
g) Make sure to use electric tools, accessories,
attachments, etc. in accordance with these
instructions. Take the conditions in your
work area and the job in hand into account.
Using electric tools for any purpose other than the
one for which they are intended can lead to
dangerous situations.
5. Service
a) Have your electric tool repaired only by
trained personnel using only genuine spare
parts. This will ensure that your electric tool
remains safe to use.
Safety Information for hammer
a) Wear ear protection. The impact of noise can
cause damage to hearing.
b) Use the additional handles supplied with the
tool. Losing control of the tool can cause injuries.
c) Hold the equipment by the insulated handles
when carrying out work during which the
14
plug-in tool could strike concealed power
cables or its own mains lead. Contact with a
live cable can also make the metal parts of the
equipment live and will cause an electric shock.
Additional Safety rules
Check that your mains voltage is the same as
n
that marked on the rating plate.
If you use a cable reel, run all the cable off the
n
reel. The minimum conductor cross section used
should be 1.5 mm 2 .
If you use this electric hammer drill outdoors you
n
must connect it using a suitable H07RN-F 3G 1.5
mm 2 extension cable with a spray-water protected
plug.
Make sure of your footing, particularly when
n
working free-handed on ladders or scaffolding.
Use a detector to localize pipes and/or cables in
n
walls with concealed electric, water or gas lines.
Avoid any contact with conducting electrical parts
or lines.
Wear ear-muffs to protect your hearing: Risk of
n
progressive loss of hearing!
Wear goggles and use a breathing mask on
n
dusty jobs.
Never use the machine near vapors or
n
combustible liquids.
Always unplug the machine before cleaning it or
n
changing drill bits etc.
Keep the power cable safe from damage. Oil and
n
acids can damage cables.
Never overload the machine.
n
Important! Follow all safety regulations in your
n
country applicable to the installation, use and
maintenance of the machine.
Chisel bits and drill bits can be inadvertently
n
thrown out from the machine and cause serious
injury:
Always check that the chisel bit or drill bit is firmly
n
locked in the chuck before you start work.
Check the chuck for wear or damage at regular
n
intervals.
Do not start a hammering tool until it is pressed
n
against a workpiece (wall, ceiling, etc.).
Always unplug the hammer drill when you have
n
finished working and remove the chisel bit or drill
bit from the tool.
Always unplug the machine before changing
n
chisel bits or drill bits etc.
Protect eyes and assistants from small flying
n
parts and splinters. Wear a helmet! Erect a
screen wall!
Use workgloves to protect fingers from crushing
n
and skin from grazing.
Vibrations can be harmful to the hand-arm
n
system: Keep the impact time of vibrations to a