Overhead Rigging - JB Systems Light Led Strobe Manual De Instrucciones

ENGLISH
DESCRIPTION:
1.Optical lens
2.Hanging bracket with 2 knobs on both sides to fasten the unit and a mounting hole to fix a mounting hook.
3.15Vdc input, connect the supplied AC/DC-mains adapter here.
4.MODE SELECTOR knob:
a) BURST-8 MODE: the unit shows burst of 8 flashes, followed by a time interval that can be adjusted
with knob (5)
b) BURST-4 MODE: the unit shows burst of 4 flashes, followed by a time interval that can be adjusted
with knob (5)
c) NORMAL STROBE MODE: normal strobe function, use knob(5) to adjust the speed.
d) MUSIC STROBE MODE: strobe works to the rhythm of the music, use knob(5) to adjust the mic
sensitivity.
5.SPEED/SENSITIVITY knob: functionality depends on the working mode:

In burst mode you can adjust the time interval between two bursts.

In normal mode you can adjust the strobe speed from 0,5Hz to 20Hz

In Music mode you can adjust the sensitivity of the internal mic.

OVERHEAD RIGGING

 Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
 Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids.
 The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
 Before rigging make sure that the installation area can hold a minimum point load of 10times the device's
weight.
 Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
 The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
 Don't cover any ventilation openings as this may result in overheating.
 The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
JB SYSTEMS
®
OPERATION MANUAL
3/26 LED STROBE
ENGLISH
OPERATING INSTRUCTIONS
 Once connected to the mains the device starts running.
 Do not switch the unit on and off in short time intervals
 Always unplug the unit when it is not used for a longer time or before replacing the bulb or start servicing.
 In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
 Important: Never look directly into the light source! Don't use the effect in the presence of persons
suffering from epilepsy.
MAINTENANCE
 Make sure the area below the installation place is free from unwanted persons during servicing.
 Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
 All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
 Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
 When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.
 The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.
 In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be
cleaned monthly.
 The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
 The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit's optics.
 Clean with a soft cloth using normal glass cleaning products.
 Always dry the parts carefully.
 Clean the external optics at least once every 30 days.
 Clean the internal optics at least every 90 days.
Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!
SPECIFICATIONS
Mains Adapter: input: AC 100- 240V, 50/60Hz
Output: 15Vdc / 700mA
Power consumption: 5 Watt
Sound Control: Internal microphone
Lamp: 68 white LEDs
Size: see drawing
Weight: 0,5 kg
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com
JB SYSTEMS
®
OPERATION MANUAL
4/26 LED STROBE