Bosch GSC 75-16 Professional Manual Original página 9

Keep cutting tools sharp and clean. Properly main-
u
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in
u
accordance with these instructions, taking into ac-
count the working conditions and the work to be per-
formed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and
u
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Safety instructions for metal shears
This power tool is not suitable for bench-mounted use.
u
It must not be clamped into a vice or fastened to a work-
bench, for example.
Only carry out work with a fitted chip deflector. Make
u
sure that the chip deflector is not damaged or bent out
of shape. Working without a chip deflector or with a dam-
aged chip deflector poses a risk of injury. Have a dam-
aged chip deflector replaced immediately by an author-
ised after-sales service centre for Bosch power tools.
Wear protective gloves during work and pay particu-
u
lar attention to the cord. Make sure that cut sheet
parts are not bent towards your body or the cord.
Sharp burrs develop on the cut sheets; these can cause
injury or damage the cord. When necessary and while
wearing gloves, press bending sheet parts away from
your body and/or from the cord.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Bosch Power Tools
Intended Use
The power tool is intended for cutting sheet metals without
incurring any loss from chipping. It is suitable for straight
and curved cuts.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) On/off switch
(2) Chip deflector
(3) Handle (insulated gripping surface)
(4) Fastening screw for upper cutter
(5) Upper cutter
(6) Bottom cutter
(7) Set screw for bottom cutter
(8) Fastening screw for bottom cutter
a)
(9) Hex key
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Sheet metal shears
Article number
Rated power input
Power output
No-load stroke rate n
0
Stroke speed under load
Max. steel sheet cutting ca-
A)
pacity
Smallest curve radius
Weight according to
EPTA-Procedure 01:2014
Protection class
A) Refers to steel sheets of up to 400 N/mm
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Noise/Vibration Information
Noise emission values determined according to
EN 62841‑2‑8.
Typically, the A-weighted noise levels of the power tool are:
Sound pressure level 87 dB(A); sound power level
98 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841‑2‑8:
2 2
a = 5.5 m/s , K = 1.5 m/s .
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
English | 9
GSC 75-16
3 601 E00 5..
W 750
W 400
-1
min 5200
-1
min 4000
mm 1.6
mm 35
kg 1.7
/Ⅱ
2
1 609 92A 6DV | (01.06.2021)