Bestway POWER STEEL 15157 Manual De Instrucciones página 5

CHOOSE THE CORRECT LOCATION
NOTE: The pool must be set up on a completely flat and level surface. Please do not install the pool if the surface is
inclined or sloped.
Correct conditions to set up the pool:
• The selected location has to be capable of uniformly supporting the weight for the entire time the pool is installed,
moreover the location must be flat and must be cleared of all objects and debris including stones and twigs.
• We recommend positioning the pool away from any objects children could use to climb into the pool.
NOTE: Position the pool near an adequate drainage system to deal with overflow or to discharge the pool.
Incorrect conditions to set up the pool:
• On uneven ground the pool may collapse causing serious personal injury and/or damage to personal property and will
void the warranty and prevent any service claims.
• Sand should not be used to create a level base; the ground must be dug out if necessary.
• Directly under overhead power lines or trees. Be sure the location does not contain underground utility pipes, lines or
cables of any kind.
• Do not set up the pool on driveways, decks, platforms, gravel or asphalt surfaces. The selected location should be firm
enough to withstand the pressure of the water; mud, sand, soft / loose soil or tar are not suitable.
• Grass or other vegetation under the pool will die and may cause odors and slime to develop, therefore we recommend
removing all grass from the selected pool location.
• Avoid areas prone to aggressive plant and weed species that may grow through the ground cloth or liner.
NOTE: Check with your local city council for by-laws relating to fencing, barriers, lighting and safety requirements and
ensure you comply with all laws.
NOTE: If have a filter pump, refer to the pump's manual for instructions.
NOTE: The ladder must match the pool size and should be used only for entering and exiting the pool. It is forbidden to
exceed the permitted payload of the ladder. Check regularly if the ladder is properly assembled.
Installation
1
C
C
C
2
F
C
E
C
C
E
E
C
E
C
3
G
H
A
B
C
A
F
F
C
F
D
G
G
4
5
6
Assembly of the Frame pool can be completed without tools.
IMPORTANT: Bestway Inflatables will not be responsible for damage caused to the pool due to mishandling or failure to
follow these instructions.
1. Lay out all parts and check that you have the correct quantities as listed in the components list. If you are missing
any parts do not assemble the pool and contact Bestway Customers Service.
2. Spread out the pool and make sure the pool is right side up; let it sit exposed to direct sunlight for 1 hour or more so
that the pool is more flexible during set up.
3. Place the pool near an adequate drainage system to deal with overflow water and ensure the pool's inlet A and outlet
B are correctly positioned to allow your filter pump to connect to a power source. Note: Do not use extension power
cords to power your pump.
ATTENTION: Do not drag the pool on the ground, this can damage the pool.
Filling Pool with Water
ATTENTION: Do not leave pool unattended while filling with water
1. Fill pool until water capacity is 90%, DO NOT OVERFILL as this could cause the pool to collapse. In times of heavy
rainfall you may need to empty some of the water to ensure the level is correct.
2. When filling the pool is completed, check that the water is not collecting on any side to ensure the pool is level.
IMPORTANT: If pool is not level, drain water and re-level ground by digging out. Never attempt to move the pool with
water in it, serious personal injury or damage to the pool may result.
WARNING: Your pool may contain a great deal of pressure. If your pool has any bulge or uneven side then the pool is
not level, the sides may burst and the water may discharge suddenly causing serious personal injury and/or damage
to property.
3. Check pool for any leaks at valves or seams, check ground cloth for any evident water loss. Do not add chemicals
until this has been done.
NOTE: In the event of a leak, patch your pool using the underwater adhesive repair patch provided. Refer to the
FAQ's for further information.
0% 30%
Proper Water Level
5
I
I
1in. - 2in.
2-5 cm
70%
0°
90%
P-S-004966