Options And Functions - Franke FDW 614 D10P DOS LP C Manual De Usuario

OPTIONS AND FUNCTIONS

OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL). If an option is not compatible with the selected
program see PROGRAMS TABLE, the corresponding LED flashes rapidly 3 times and beeps will sound. The option will not be enabled.
MULTIZONE
If there are not many dishes to be washed, a half loading may
be used in order to save water, electricity and detergent.
Select the program and then press the MULTIZONE button: the symbol
of the chosen rack will appear on the display.
By default the appliance washes dishes in all racks.
To wash only the specific rack, press this button repeatedly:
shown on the display (only lower rack)
shown on the display (only upper rack)
shown on the display (only cutlery rack)
shown on the display (option is OFF and the appliance will wash
dishes in all racks).
Remember to load the upper or lower rack only, and to reduce
the amount of detergent accordingly.
If upper rack is removed, please apply detergent directly to tub
instead of detergent dispenser.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DELAY
The start time of the program may be delayed for a period of time
between 1 and 12 hours.
1. Press the DELAY button: the corresponding «h» symbol appears on
the display; each time you press the button, the time (1h, 2h, etc. up
to max. 12h) from the start of the selected wash cycle will be increased.
2. Select the wash program, press the START/PAUSE button and within
4 seconds close the door: the timer will begin counting down.
3. Once this time has elapsed, the indicator light «h» switches off
and the wash cycle begins.
To adjust the delay time and select a shorter period of time, press
the DELAY button. To cancel it, press the button repeatedly until
the selected delayed start indicator light «h» switches off.
The DELAY function cannot be set once a wash cycle has been
started.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TURBO
This option can be used to reduce the duration of the main programs
while maintaining the same washing and drying performance levels.
After selecting the program, press the TURBO button and the indicator
light will switch on. To deselect the option, press the same button again.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EXTRA DRY
To improve the drying of the dishes, after selecting the program,
press the EXTRA DRY button and the indicator light comes on.
A higher temperature during the final rinse and an extended
drying phase allow for improving drying. To deselect the option,
press the same button again. The EXTRA DRY option results
in the lengthening of the wash cycle.
TABLET (Tab)
This setting allows you to optimize the performance
of the program according to the type of detergent used.
Press the START/PAUSE button for 3 seconds (the corresponding symbol
will light up) if you use combined detergents in tablet form (rinse aid,
salt and detergent in 1 dose).
If you use powder or liquid detergent, this option should be off.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPERATION INDICATOR
A LED light projected on the floor indicates that
the dishwasher is working. One of the following operating
modes can be selected:
a) Disabled function.
b) When the cycle starts the light goes on for few seconds, stays off
during the cycle and flashes at the end of the cycle.
c) The light stays on during the cycle and flashes at the end of the cycle
(default mode).
If the delayed start was set, the light goes on either for the first few
seconds or the entire duration of the countdown, based on whether
mode b) or c) was set.
The light goes off every time the door is opened. To select the mode
you prefer, switch on the machine, hold down button P until one
of the three letters appears on the display, press button P until you
reach the desired letter (or mode), hold down button P to confirm
the selection.
Note: If CoolDry is active and it opens the door, then Operation
Indicator will not flash at the end of cycle.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CoolDry
CoolDry is a convection drying system which automatically opens
the door during/after drying phase to ensure exceptional drying
performance every day. Door opens at the temperature that is safe
to your kitchen furniture, thus door will not be opened when the option
of TURBO is on.
As additional steam protection, special designed protection foil is added
together with the dishwasher. To see how to mount protection foil
please refer to (INSTALLATION GUIDE).
CoolDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding P
button (6 sec).
2. You are currently in Light Control Menu (please refer to OPERATION
INDICATOR description), if you don't want to change anything
please press and hold P button (until one of the two letters appears
on the display).
3. You switched to CoolDry Control Menu, you could change status
of CoolDry functionality by pressing P button:
E – enabled d – disabled
To confirm the change and exit from the Control Menu please press
and hold P button (3 sec).
EN
7