Bosch GSS 23 A Professional Manual Original página 13

Ocultar thumbs Ver también para GSS 23 A Professional:
Tabla de contenido

Publicidad

OBJ_BUCH-384-002.book Page 13 Thursday, February 19, 2015 11:38 AM
Replacing the Sanding Sheet
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
Sanding Sheets without Velcro Backing
(see figures C – E)
 Press the release button 8 and keep it depressed.
 Guide the sanding sheet 7 to the stop under the opened
front clamping bracket 9 and let go of the release button
8 again. Pay attention that the sanding sheet is clamped
centrally.
 Press the release lever 5 and keep it depressed.
 Place the sanding sheet 7 firmly around the sanding
plate. Guide the other end of the sanding sheet 7 under
the opened rear clamping bracket 4.
 Hold the sanding sheet and let go of the release lever 5 to
lock the sanding sheet.
Sanding sheets without holes, e. g. from rolls or by the metre,
can be punctured with the perforating tool 13. For this, push
the power tool with the sanding sheet mounted onto the per-
forating tool (see figure F).
To remove the sanding sheet 7, press the release lever 5 and
pull the sanding sheet out of the rear clamping bracket. Push
the release button 8 and remove the sanding sheet complete-
ly.
Selecting the Sanding Sheet
Depending on the material to be worked and the required rate
of material removal, different sanding sheets are available:
For the working of all wooden
materials
For coarse-sanding, e. g. of rough,
unplaned beams and boards
For face sanding and planing small
irregularities
For finish and fine sanding of hard
woods
For the working of paint/enamel
coats or primers and fillers
For sanding off paint
For sanding primer
For final sanding of primers before
coating
Replacing the Sanding Plate (see figure G)
The sanding plate 6 can be replaced, if required.
Unscrew the 4 screws 14 completely and remove the sanding
plate 6. Attach the new sanding plate 6 and tighten the screws
again.
Bosch Power Tools
Operation
Starting Operation
 Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Switching On and Off
To start the machine, press the On/Off switch 1 and keep it
pressed.
To lock the pressed On/Off switch 1, press the lock-on button
2.
To switch off the machine, release the On/Off switch 1 or
when it is locked with the lock-on button 2, briefly press the
On/Off switch 1 and then release it.
To save energy, only switch the power tool on when using it.
Working Advice
 Wait until the machine has come to a standstill before
placing it down.
 Before any work on the machine itself, pull the mains
plug.
The removal capacity during sanding is mainly determined by
the selection of the sanding sheet.
Only flawless sanding sheets achieve good sanding capacity
and extend the service life of the machine.
Pay attention to apply uniform sanding pressure; this increas-
es the working life of the sanding sheets.
Intensifiying the sanding pressure does not lead to an in-
Grain size
crease of the sanding capacity, but to increased wear of the
machine and the sanding sheet.
A sanding sheet that has been used for metal should not be
used for other materials.
40 – 240
Use only original Bosch sanding accessories.
coarse
40, 60
Maintenance and Service
80, 100,
medium
120
Maintenance and Cleaning
 Before any work on the machine itself, pull the mains
fine
180, 240
plug.
 For safe and proper working, always keep the machine
and ventilation slots clean.
If the replacement of the supply cord is necessary, this has to
40 – 320
be done by Bosch or an authorized Bosch service agent in or-
coarse
40, 60
der to avoid a safety hazard.
80, 100,
medium
120
After-sales Service and Application Service
180, 240,
In all correspondence and spare parts order, please always in-
fine
320
clude the 10-digit article number given on the type plate of
the machine.
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
English | 13
1 609 92A 15L | (19.2.15)

Publicidad

Tabla de contenido
loading

Tabla de contenido