WALTHER PILOT PILOT Maxi Instrucciones De Servicio página 12

Contents
Exploded Drawing
Declaration of CE-Conformity
Replacement parts
1 General
1.1 Identification of model version
1.2 Normal use
1.3 Improper use
2 Technical description
3 Safety Instructions
3.1 Identification of safety instructions
3.2 General Safety Instructions
4 Connection of input lines
5 Operational handling
6 Adjusting the spray pattern
6.1 Correction of spray pattern imperfections
7 Trouble shooting
8 Retooling and repairs
9 Cleaning
10 Disposal of cleaning and servicing substances
11 Technical data
2
23
24
28
28
28
29
29
21
21
22
31
31
32
33
33
34
35
36
36
22
Declaration of CE-Conformity
We, the manufacturers of the equipment, hereby declare under our sole responsibility that
the product(s) described below conform to the essential safety requirements. This declaration will
be rendered invalid if any changes are made to the equipment without prior consultation with us.
Manufacturer WALTHER Spritz- und Lackiersysteme GmbH
Kärntner Str. 18 - 30
D - 42327 Wuppertal
Tel.: +49(0)202 / 787 - 0
Fax: +49(0)202 / 787 - 2217
www.walther-pilot.de • e-mail: info@walther-pilot.de
Type Designation Manual spray guns PILOT Maxi / -HVLP / -MP
PILOT Maxi
PILOT Maxi
PILOT Max
PILOT Maxi-MP
PILOT Maxi-MP
PILOT Maxi-MP
PILOT Maxi-HVLP
PILOT Maxi-HVLP
PILOT Maxi-HVLP
PILOT Maxi-K
PILOT Maxi-K
PILOT Maxi-HVLP-K
PILOT Maxi-HVLP-K
PILOT Maxi-HVLP-K
Intended purpose Processing of sprayable media
Applied Standards and Directives
EU-Mechanical Engineering Directives 2006 / 42 / EC
94 / 9 EC (ATEX Directives)
DIN EN ISO 12100-1
DIN EN ISO 12100-2
DIN EN 1127-1
Specification according 94 / 9 / EC
Category 2 Part marking
Authorized with the compilation of the technical file:
Nico Kowalski, WALTHER Spritz- und Lackiersysteme GmbH, Kärntner Str. 18 - 30
D- 42327 Wuppertal
Special remarks :
The named product is intended for installation in other equipment. Commissioning is prohibited
until such time as the end product has been proved to conform to the provision of the Directives
2006 / 42 / EC.
Wuppertal, the 1st of January 2010
i.V.
Name: Torsten Bröker
Position: Manager, Design and Development
This Declaration does not give assurance of properties in the sense of product liability. The safety instructions
provided in the product documentation must be observed at all times.
Gravity-feed cup
Material connection
Suction cup
Gravity-feed cup
Material connection
Suspended pressure cup
Gravity-feed cup
Material connection
Suspended pressure cup
Material connection
Gravity-feed cup
Material connection
Suspended pressure cup
Gravity-feed cup
DIN EN 1953
DIN EN 13463-1
Tech.File,Ref.:
II 2 G c T 6
2404
23
V 11 613
V 11 614
V 11 619
V 11 615
V 11 616
V 11 617
V 11 633
V 11 634
V 11 635
V 11 618
V 11 626
V 11 620
V 11 622
V 11 623