Inspection And Maintenance - Hitachi NC 40G Instrucciones De Manejo

English
2 Lock follower back in magazine and remove
fasteners.
3 Loosen the knob and lower toward the handle.
(See Fig. 17)
4 Pull magazine away from the firing head, and clear
jam. (See Fig. 18)
5 Connect the fuel cell and the battery to the Nailer.
ALWAYS WEAR SAFETY GLASSES.
HOW TO USE THE NOSE CAP
WARNING
Before attaching or removing the nose cap, be sure
to take your finger off the trigger and remove the fuel
cell and battery.
NOTE
Keep the nose cap on when driving nails into slippery
materials such as thin steel sheets.
Remove the nose cap when driving nails into wood.
(1) Removing/Attaching the nose cap
The nose cap is attached simply by pressing it onto
the push lever. (See Fig. 19)
To remove, insert a screwdriver or similar into the
gap between the nose cap and the push lever and
lever off. (See Fig. 20)

INSPECTION AND MAINTENANCE

CAUTION
Be sure to remove the battery and fuel cell during
clearing jams, inspection, maintenance and cleaning.
1. Inspecting the magazine
1 DISCONNECT BATTERY and FUEL CELL.
2 Clean the magazine. Remove any plastic chips and
concrete dust which may have accumulated in the
magazine. Lubricate it with Hitachi gas strip nailer
lubricant.
2. Check on mounting screws for each part
At regular intervals check every part for loose mounting
screws. Retighten any loose screws. Operating the
equipment with loose screws untightened will incur
a hazard.
3. Inspecting the push lever
Check if the push lever can slide smoothly.
Clean up the sliding area of the push lever and use the
provided oil for lubrication from time to time.
Lubrication enables smooth sliding and simultaneously
serves to prevent the formation of rust.
4. Storing (See page 8)
When not in use for an extended period, apply a thin
coat of the lubricant to the steel parts to avoid rust.
Do not store the Nailer in a cold weather environment.
Keep the tool in a warm area.
When not in use, the tool should be stored in a warm
and dry place.
Keep out of reach of children.
5. Service parts list
CAUTION
Repair, modification and inspection of Hitachi Power
Tools must be carried out by a Hitachi Authorized
Service Center.
This Parts List will be helpful if presented with the
tool to the Hitachi Authorized Service Center when
requesting repair or other maintenance.
13
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
MODIFICATIONS
Hitachi Power Tools are constantly being improved
and modified to incorporate the latest technological
advancements.
Accordingly, some parts may be changed without
prior notice.
APPLICABLE LUBRICANTS
Use HITACHI Gas Nailer lubricant.
Do not use detergent oil or additives.
These lubricants will harm the O-rings and other rubber
parts. This will cause the tool malfunction.
Noise Information
Noise characteristic values in accordance with EN 792-
13, JUNE, 2000:
The typical A-weighted single-event sound power level
The typical A-weighted single-event emission sound
pressure level at work station
These values are tool-related characteristic values and
do not represent the noise development at the point of
use. Noise development at the point of use will for
example depend on the working environment, the
workpiece, the workpiece support and the number of
driving operations, etc.
Depending on the conditions at the workplace and the
form of the workpiece, individual noise attenuation
measures may need to be carried out, such as placing
workpieces on sound-damping supports, preventing
workpiece vibration by means of clamping or covering,
etc.
In special cases it is necessary to wear hearing protection
equipment.
Vibration Information
The typical vibration characteristic value in accordance
with EN 792-13, JUNE, 2000: 3.5 m/s
This values is a tool-related characteristic value and does
not represent the influence to the hand-arm-system
when using the tool. An influence to the hand-arm-system
when using the tool will for example depend on the
gripping force, the contact pressure force, the working
direction, the adjustment of energy supply, the workpiece,
the wrokpiece support.
L ,1s,d = 108 dB
WA
L ,1s,d = 99 dB
pA
2