Publicidad

Enlaces rápidos

Instructivo de
SDS Plus
Hammer Drill
RPLUS-4NX
CAUTION
Read this manual thoroughly
before using the tool.
4
Joules
Impact energy
Applies for:
Code
Model
101220
RPLUS-4NX

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Truper Expert SDS Plus RPLUS-4NX

  • Página 1 Instructivo de SDS Plus Joules Hammer Drill Impact energy RPLUS-4NX Applies for: Code Model 101220 RPLUS-4NX Read this manual thoroughly CAUTION before using the tool.
  • Página 2: Tabla De Contenido

    Contents CAUTION Technical Data Power requirements To gain the best performance of the tool, prolong the duty life, General power tool safety warnings make the Warranty valid if necessary, and to avoid hazards Safety warnings for of fatal injuries please read and the use of hammer drills understand this Manual before using the tool.
  • Página 3: Technical Data

    Technical Data RPLUS-4NX Code 101220 Description Hammer Drill SDS Plus Chuck SDS Plus Voltage 127 V~ Frequency 60 Hz Current Power Impact energy 1000 W 4 Joules Weight 11 lb Speed Rotation: 650 RPM - 1 000 RPM Impact: 2800 strokes/min - 4 320 strokes/min Work cycle 50 minutes work per 20 min rest.
  • Página 4: General Power Tool Safety Warnings

    General power tool safety warnings WARNING! Read carefully all safety warnings and instructions listed below. Failure to comply with any of these warnings may result in electric shock, fire and / or severe damage. Save all warnings and instructions for future references.
  • Página 5: Safety Warnings For The Use Of Hammer Drills

    Safety warnings for the use of Hammer Drills Choose the appropriate drill or attachment While operating the hammer drill CAUTION • The tool is designed to work with bits CAUTION • Hold the tool by its handle and by or accessories with SDS-plus shanks. Choose the the auxiliary handle.
  • Página 6: Parts

    Parts Function Vibration Anti-skid Selector deposit Absorber handle SDS Plus Chuck Depth Trigger control rod Switch Spare carbon brushes Auxiliary Handle Power cable protection Grease tube Power Speed adjustment button / Cord LED Power Indicator Mounting and Adjustments Auxiliary Handle Operate the power tool only with the CAUTION auxiliary handle installed.
  • Página 7 Mounting and Adjustments Mounting bits and accessories CAUTION To prevent accidents, confirm that the switch is turned off and disconnect the plug from the power supply. WARNING Always wear gloves when changing accessories. They can become extremely hot during operation. •...
  • Página 8: Start Up

    Start Up Function Selector • Be sure to use the function selector (A) only when the motor is completely stopped. WARNING On no reason try to adjust the function selector with the motor running, the tool could rotate abruptly, causing unexpected accidents. •...
  • Página 9: Maintenance

    Start Up Safety Clutch Additional Information The tool has a safety clutch, which interrupts spindle power • SDS-Plus accessories require freedom to move within the (causing a rattling noise), if the accessory jams. Should this bit, which causes eccentricity when the tool is unloaded. possibility occur: However, the accessory automatically centers itself during •...
  • Página 10: Notes

    Notes ENGLISH...
  • Página 11: Authorized Service Centers

    In the event of any problem contacting a Authorized Service Center, please see our webpage www.truper.com to get an updated list, or call our toll-free numbers 800 690-6990 or 800 0187-8737 to get information about the nearest Service Center. DE TODO PARA LA CONSTRUCCIÓN FIX FERRETERÍAS...
  • Página 12: Warranty Policy

    . Transportation costs resulting from compliance of this warranty will be covered by For questions or comments, call 800-690-6990. Made in China. Imported by Truper S.A. de C.V. Parque Industrial 1, Jilotepec, Edo. de Méx. C.P. 54240 Stamp of the business.

Este manual también es adecuado para:

101220

Tabla de contenido