Publicidad
Enlaces rápidos
ENGLISH USER INSTRUCTIONS & PARTS LISTING
Voltage: 110
Phase: 1
Cycles: 50/60
Variable Speed
to 4500 RPM
SM645-1P ENDURO
Copyright © 2011 Enduro
SM645-1P & SM645-2P
SERVO MOTOR WITH POSITIONER
TM
SM645-1P
PRO
™
Servo Motor
™
www.endurosaves.com
SM645-2P
Voltage: 220
Phase: 1
Cycles: 50/60
Variable Speed
to 4500 RPM
SM645-2P ENDURO
INSTRUCTIONS - PAGE 2 >
PARTS LISTING - PAGE 13 >
TM
TM
PRO
™
Publicidad
Manuales relacionados para Enduro PRO SM645-1P
Resumen de contenidos para Enduro PRO SM645-1P
- Página 1 Phase: 1 Cycles: 50/60 Cycles: 50/60 Variable Speed Variable Speed to 4500 RPM to 4500 RPM SM645-1P ENDURO SM645-2P ENDURO ™ ™ INSTRUCTIONS - PAGE 2 > PARTS LISTING - PAGE 13 > Copyright © 2011 Enduro Servo Motor ™ www.endurosaves.com...
- Página 2 POSITIONER USER INSTRUCTIONS Congratulations! You have purchased the Enduro™ Pro SM600 series motor that pays for itself with a remarkable 60% to 80% energy savings compared to clutch motors. With the high and rising cost of electricity, you just can’t afford to run a clutch motor any longer. The power and dependability of the brushless Enduro™...
- Página 3 ENGLISH - 3 Wiring For 110 volt single phase motor follow the diagram below: For 220 volt single phase motor follow the diagram below: Note: When wiring the motor to the power source, connect both the black and white wires to achieve 220 Volts (green to ground).
- Página 4 4 - ENGLISH Motor Rotating Direction Setting Setting up Number 2 a. Keep "▼" button pressed for several seconds, until LED display indicates "S.0". b. Press "▲" button 2 times to indicate "S.2", which means "Setting up No. 2". c. Press "▼" button and LED will indicate "r.E" or "r.P" Press "▼/▲"...
- Página 5 ENGLISH - 5 Option A - Setting Slow Starting Speed via Motor Control a. Keep "▼" button pressed for several seconds, until LED display indicates "S.0". b. Press "▲" button 1 time to indicate "S.1", which means "Setting up No. 1". c.
- Página 6 6 ENGLISH Maximum Speed Setting Setting up Number 3 a. Keep "▼" button pressed for several seconds, until LED indicates show "S.0". b. Press "▲" button 3 times to indicate "S.3", which means "Setting up No. 3". c. Then press "▼" button and LED indicates "XX"(XX is 1-45), which means the highest motor speed in RPM.
- Página 7 ENGLISH - 7 Installation of Positioner on SM645-1P & SM645-2P 1. Be sure the female power cord is disconnected from the power inlet socket. 2. Remove the screw on the machine pulley. Install the sensor adapter (supplied) onto the pulley with the adapter screw (supplied).
- Página 8 8 - ENGLISH Needle Position Setting a. At any time when the motor is on but not running, press the up button "▲". If the LED indicates: "P.u" it means the needle position setting alternate "ready" status is POSITION UP when the sewing machine is stopped. Either "P.d"...
- Página 9 9 - ENGLISH E1: Motor Control Error Most E1 error messages occur because of unstable power being supplied to the motor. • Release the pedal when the E1 error message occurs, then push down again to activate the motor. If the E1 error message no longer appears this was a False error due to unstable power.
- Página 10 10 - ENGLISH E5: Display Module and Control Module Communications Error It is possible to receive an E5 error message from unstable power which means it is a False error and the problem should resolve on its own. E5 error message indicates a faulty LED display. •...
- Página 11 11 - ENGLISH E8: The Down Position Has No Signal It is possible to receive an E8 error message which means that the down position has no signal. • Check the connection of the synchronizer. Make sure it it is properly plugged into the back of the motor. •...
- Página 12 ENGLISH - 12 Treadle Sensor Installation Description with Diagrams (Proper Replacement of Treadle Sensor) 1. Remove the 4 screws on the treadle sensor 2. Check the channel sensor. It should have plate. a red light when the cable is connected to the motor circuit board and the motor is powered on.
- Página 13 ENGLISH - 13 SM645-1P & SM645-2P PARTS LISTING Fig. Description SM76 Sensor only with screws (dual channel for motors with positioner) SM604 Treadle Sensor Plate Assembly complete with 4 screws (dual channel for motors with positioner) (431U) SM77 Replacement positioner sensor kit complete SM618 Complete wire harness for 110 volt models, fused (PF Gray) SM619...