Narex VYS 30-21 Instrucciones De Uso Originales página 15

We recommend to connect the appliance via the current protector. The plug
and the power and connecting cable connectors have to be waterproof.
For purpose of cable extension only the cable corresponding to manufactur-
er's specification or a cable of higher quality may be used.
When using the extension cable, observe the minimum cross-section values:
cable length
< 16 A
up to 20 m 1,5 mm
20 to 50 m 2,5 mm
Prior to putting into operation
Vacuum cleaner completion
1. Unpack the appliance and its accessories.
2. The power cable may not be connected to the
socket for now.
3. Loosen the fasteners (A) and remove the top
vacuum cleaner part.
4. Unpack the accessories and take them out of
the vacuum cleaner canister.
Insertion of the filter bag
1. The power cable may not be connected to the
socket for now.
2. Loosen the fasteners (A) and remove the top
vacuum cleaner part.
3. Put the filter bag into the vacuum cleaner can-
ister.
4. Press the filter bag neck firmly onto the hole
for hose connection.
5. Place the top part on the vacuum cleaner.
6. Close the fasteners (A). Check whether the fas-
teners are fixed firmly.
Operation
Connection of suction hose and connection to
the power supply source
1. Connect the suction hose.
2. Plug the power cable into the correctly in-
stalled socket (with the safety pin); the vacu-
um cleaner must be OFF.
cross section
< 25 A
2,5 mm
2 2
4,0 mm
2 2
Starting the appliance
Switch position Function
Suction force control
Switch position Function
Automatic operation with connected attachments
1. The vacuum cleaner and the el. tool (attach-
ment) must be OFF prior to interconnecting
them.
2. Connect the el. tool to the suction hose already
connected with the vacuum cleaner.
3. Plug the el. tool power cable into the socked in
the vacuum cleaner control panel.
4. Start the vacuum cleaner, the switch is in the
position "auto".
5. Start the el. tool. Vacuum cleaner motor will
auto
be started at the same time. After switching
the el. tool off, the vacuum cleaner will run for
a while to move the dust from the suction hose
into the canister.
Cleaning the filter cartridge „Press & Clean"
VYS 30-21
Applicable only if the appliance runs with the filter without the filter bag.
In case of suction power drop:
1. Turn the switch (6) to the position "I" (max. suction power).
2. Close the suction hose hole by your palm.
3. Depress the switch three times to start filter cleaning (8). This way gener-
ated airflow will clear the filtration cartridge plates for deposited dust.
Cleaning the filter cartridge „Auto Clean"
VYS 30-71 AC
To ensure that suction performance is always at its best, the filter element is
automatically cleaned during operation. We recommend complete cleaning if
the filter element becomes extremely dirty.
1. Switch off the vacuum cleaner.
2. Close the nozzles or suction hose opening with the palm of your hand.
3. Turn the switch (6) to position „I" and let the cleaner operate for approx.
10 seconds with the suction hose opening closed.
After work completion
Vacuum cleaner switching off and storing
1. Switch the appliance off and disconnect the
power cable from the socket.
2. Wind the cable on the handle (A). Start wind-
ing from the vacuum cleaner and not from the
cable end to prevent cable twisting.
3. Empty the canister and clean the vacuum
cleaner.
4. After suction of liquids: put the top vacuum
cleaner part aside to let the filter cartridge
dry.
5. Place the vacuum cleaner in a dry room and
protect from misuse by unauthorized persons.
English
0 OFF
auto automatic mode
I ON
The suction force control
mechanism enables to adapt
the suction power to specific
conditions
15