Bosch EasyImpactDrive 12 Manual Original página 13

Cordless Impact
Driver
– Setting 1 rpm
– Setting 2 rpm
Impact rate
– Setting 1 rpm
– Setting 2 rpm
Maximum torque, hard Nm
screwdriving applica-
tion according to
ISO 5393
Machine screw dia- mm
meter
Max. screw diameter mm
Tool holder
Weight according to kg
EPTA-Procedure
01:2014
Permitted ambient temperature
– While charging °C
– During operation and °C
storage
Recommended batter-
ies
Recommended char-
gers
(Limited performance
at temperatures < 0 °C)
Noise/vibration information
Noise emission values determined according to EN
62841-2-2.
Typically the A-weighted noise level of the power tool is:
88 dB(A); sound power level 99 dB(A). Uncertainty K =
3 dB.
Wear hearing protection!
Total vibration values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-2:
Impact tightening of fasteners of the maximum capacity of
2
the tool: a <9,5 m/s , K=1,5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure detailed in EN 62841
and may be used to compare power tools. They may also be
used for a preliminary estimation of vibration and noise
emissions.
The given vibration level and noise emission value represent
the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
Bosch Power Tools
increase the vibration and noise emissions over the total
EasyImpactDrive 12
working period.
To estimate vibration and noise emissions accurately, the
0 - 1400
times when the tool is switched off or when it is running but
0 - 2800
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
0 - 2400
Implement additional safety measures to protect the oper-
0 - 3300
ator from the effects of vibration, such as servicing the
100
power tool and application tools, keeping the hands warm,
and organising workflows correctly.
Assembly
M4–M12
Removing the battery (see figure A)
6
u
¼" internal hexagon
1.0
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
0 to +45
reducing its service life. Interrupting the charging process
-20 to +50
does not damage the battery.
The lithium-ion battery is protected against deep discharge
PBA 10.8 V ...
by the Electronic Cell Protection (ECP). A protective circuit
PBA 12 V ...
switches the cordless dust extractor off when the battery is
drained.
u
AL 11.. CV
GAL 1220
To remove the battery (5), press the release button (4) and
pull the battery downwards out of the power tool. Do not
use force to do this.
Follow the instructions on correct disposal.
Changing the Tool
u
Inserting the application tool (see figure B)
Pull the locking sleeve (2) forward, guide the application tool
2
(1) into the tool holder up to the stop and release the locking
sleeve (2) to lock the application tool.
Screwdriver bits (12) can be inserted using a universal bit
holder with ball catch (11).
Removing
Pull the locking sleeve (2) forward and remove the applica-
tion tool.
Use only the chargers listed on the accessories page.
Only these chargers are matched to the lithium-ion bat-
tery of your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
1 609 92A 480 | (04.07.2018)
English | 13