Descargar Imprimir esta página

Husqvarna SE-561 82 Manual De Instrucciones página 6

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 51
OPERATION
ENGINE ADJUSTMENTS (Fig.K
Refer to the engine manufacturer's maintenance
manual.
CAUTION:- 0.6l Oil must be added to the
engine before use
STARTING THE ENGINE (Fig.K
Once the machine has been set up properly, start the
engine as follows:
a) Engines with choke system:
when the engine is cold, position the accelerator lever
(Fig.K
- pos.13) on START
III
b)Operate the engine stop lever (14) to prepare the
engine for start, keep lever pressed against handle
while starting and using the machine (it operates the
engine brake).
c) Engines with primer system:
Press the fuel-enrichment pump (21) located on the
carburettor 3 or 4 times position the accelerator lever
(13) on MAX.
For further information and explanations, read carefully
the user instruction manual of the engine.
d) Start engine.
MANUAL STARTING: (While holding the engine stop
lever (14)).
 Hold the engine start-grip (11) and pull the starter rope
gently until you feel the resistance caused by compres-
sion. Return the starter rope slowly then pull the handle
firmly towards you to its full extent.
ELECTRICAL STARTING: (While holding the engine
stop lever (14)).
 Insert the plug (G) in the socket (H) on the engine.
Turn the ignition key (17).
ADJUSTMENT OF CLUTCH CABLE
Important: If, when you press the clutch lever, the automatic advance gear does not engage, the clutch cable should
be adjusted by inserting the spring (P) in one of the subsequent holes in the plate (R) or in the hole "S" .
MAINTENANCE
 For a four stroke engine, check the oil level and change
the oil when dirty. For further explanation, see ENGINE
INSTRUCTION BOOK.
 Frequently check the mower and ensure that all grass
deposits are removed from beneath the deck.
 Never clean the mower by pouring water over it: this may
seriously damage the electric start system.
 Take care, the exhaust muffler may be very hot.
 Frequently check the blade for damage.
4
ENGLISH -
)
I
)
II
(for self-propelled versions only)
Caution! Switch off the motor and disconnect
the spark plug before undertaking any mainte-
nance work.
CAUTION: The blade starts turning as soon
as the engine is started.
Keep the engine stop lever (14) depressed during machine
operation.
MOWING (Fig.K
K
)
III -
Iv
To cut the grass, push the lawn mower manually or insert
the automatic advance gear.
How to insert automatic advance: Lift up the clutch
handle (18) and keep it pressed in position.
CAUTION: Engage the gear only when the
engine is running.
How to disengage advance: Release the clutch han-
dle.
VERSION WITH BLADE BRAKE (Fig.K
With engine running, pull the handle (14) towards the bar
and keep depressed. Push the blade engagement lever
(19) forward to make the blade rotate.
WARNING! When the handle (14) is released
the blade stops while the motor continues
running.
MOWING
To cut the grass, push the lawn mower manually or insert
the automatic advance gear.
How to insert automatic advance: Lift up the clutch
handle (18) and keep it pressed in position.
CAUTION: Engage the gear only when the
engine is running.
How to disengage advance: Release the clutch han-
dle.
 The lawn mower must be checked by a SERVICE
DEALER.
 Cleaning under the bodywork
With machine at a standstill and off.
- Attach fitting (22) on the deck to the water supply tap.
Turn on the tap.
- start up the motor (blade in rotation), allowing it to
warm up for a few minutes.
- at the end of cleaning switch off the motor, turn off the
tap, detach the tube from the deck connection..
)
V

Publicidad

loading