Specifications - Campbell Hausfeld Tl050189 Instrucciones De Operación

Operating Instructions
important safety instructions
(Continued)
GEnERal
a . To reduce the risks of
electric shock, fire, and
injury to persons, read all
the instructions before
using the tool.
b . Be thoroughly familiar with the
controls and the proper use of the
equipment . Follow all instructions .
Contact your Campbell Hausfeld
representative if you have any
questions .
c . Only persons well acquainted with
these rules of safe operation should
be allowed to use the unit .
Read and
understand tool
labels and manual. Failure to follow
warnings, dangers, and cautions
could result in DEATH or SERIOUS
INJURY.
WoRK aREa
a . Keep the work area clean and well
lighted. Cluttered benches and dark
areas increase the risks of electric
shock, fire, and injury to persons .
b . Do not operate the tool
in explosive atmospheres,
such as in the presence of
flammable liquids, gases,
or dust. The tool is able to create
sparks resulting in the ignition of
the dust or fumes .
Tool Components and specifications
Avg SCFM & psi . . . . . . . . 4 .8 @ 90 PSIG
Continuous SCFM . . . . . . 19 .2 @ 90 PSIG
Minimum Rated RPM . . . . . . . . . . . . 140
Max Torque . . . . . . . . . . . . . . . . .50 ft .lb .
Working Torque . . . . . . . . . 10-45 ft .lb .
Gear Type . . . . . . . . . . 3 Idler Planetary
Bolt Capacity . . . . . . . . . . . . . . . .3/8 inch
Air Inlet . . . . . . . . 1/4 inch NPT (Female)
Min . Hose Size . . . . . . . . . . . . . .3/8 inch
Drive . . . . . . . . . . . . . . . . . . . 3/8 inch sq .
Weight . . . . . . . . . . . . . . . . . . . . 2 .5 lbs .
www.chpower.com
c . Keep bystanders, children, and
visitors away while operating the
tool. Distractions are able to result in
the loss of control of the tool .
pERsonal safETY
a . Stay alert. Watch what you are
doing and use common sense
when operating the tool. Do not
use the tool while tired or under
the influence of drugs, alcohol,
or medication. A moment of
inattention while operating the
tool increases the risk of injury to
persons .
b . Dress properly. Do not wear loose
clothing or jewelry. Contain long
hair. Keep hair, clothing, and
gloves away from moving parts.
Loose clothes, jewelry, or long
hair increases the risk of injury to
persons as a result of being caught
in moving parts .
c . Avoid unintentional starting.
Be sure the switch is off before
connecting to the air supply. Do not
carry the tool with your finger on
the switch or connect the tool to the
air supply with the switch on .
d . Remove adjusting keys or wrenches
before turning on the tool. A key or
wrench attached to a rotating part
of the tool may result in personal
injury .
(25% usage)
(100% usage)
Forward/Reverse Dial
e . Do not overreach. Keep proper
f . Use safety equipment. A dust mask,
g . Always wear eye
h . Always wear hearing
i . Do not attach the hose or tool to
position when using or handling
the tool.
of work with the tool. Stop using
the tool if you feel pain in hands or
arms.
j . Hold tool by insulated gripping
3/8 inch Anvil
2
footing and balance at all times.
Proper footing and balance enables
better control of the tool in
unexpected situations .
non-skid safety shoes and a hard
hat must be used for the applicable
conditions .
protection.
protection when using
the tool. Prolonged
exposure to high intensity
noise is able to cause
hearing loss .
your body. Attach the hose to the
structure to reduce the risk of loss of
balance if the hose shifts .
Always remain in
a firmly balanced
Avoid long
extended periods
surface when performing an
operation where the tool may
contact hidden wiring. Contacting a
"live" wire will make exposed metal
parts of the tool "live" and shock
the operator .
Air Inlet
Throttle
Exhaust