Campbell Hausfeld TL140289 Instrucciones De Funcionamiento

See Warranty on page 6 for important information about commercial use of this product.
Operating Instructions
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
REGISTER YOUR PRODUCT ONLINE NOW!
Table of Contents
Description . . . . . . . . . . . . . . . . . . . . . .1
Unpacking . . . . . . . . . . . . . . . . . . . . . . .1
Safety Guidelines . . . . . . . . . . . . . . . . .1
General Safety Information . . . . . . . 1-2
Operation . . . . . . . . . . . . . . . . . . . . . . .2
Storage . . . . . . . . . . . . . . . . . . . . . . . . .3
Troubleshooting Chart . . . . . . . . . . . . .4
Warranty . . . . . . . . . . . . . . . . . . . . . . . .6
Description
Impact wrenches are air tools designed
for removing and installing nuts and
bolts . Impact wrenches have different
impact mechanism types such as rocking
dog, pin clutch and twin hammer
(double jumbo) .
The rocking dog and pin clutch types
are used as general purpose tools by
DIY'ers and hobbyists . Twin hammer
wrenches are for use by the professional
in tire shops, assembly line applications
and for removing high torque bolts .
Unpacking
When unpacking this product, carefully
inspect for any damage that may have
occurred during transit . Make sure any
loose fittings, bolts, etc ., are tightened
before putting this product into service .
READ & FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
DO NOT DISCARD
Safety Guidelines
This manual contains information
that is very important to know and
understand . This information is
provided for SAFETY and to PREVENT
© 2012 Campbell Hausfeld/Scott Fetzer
EQUIPMENT PROBLEMS . To help
recognize this information, observe the
following symbols .
hazardous situation which, if not
avoided, WILL result in death or serious
injury.
hazardous situation which, if not
avoided, COULD result in death or
serious injury.
hazardous situation which, if not
avoided, MAY result in minor or
moderate injury.
information, that if not followed, may
cause damage to equipment.
NOTE: Information that requires special
attenion
General Safety Information
CALIFORNIA PROPOSITION 65
dust when you cut, sand, drill
or grind materials such as
wood, paint, metal, concrete,
cement, or other masonry. This dust
often contains chemicals known to
cause cancer, birth defects, or other
reproductive harm. Wear protective
gear.
GENERAL SAFETY
This product is a part of a high pressure
system and the following safety
precautions must be followed at all
times along with any other existing
safety rules .
REMINDER: Keep your dated proof of purchase for warranty purposes!
Attach it to this manual or file it for safekeeping.
For parts, product & service information
visit www.chpower.com
Impact
Wrenches
http://www.chpower.net/reg
1 . Read all manuals included
Danger indicates an
imminently
2 . Only persons well acquainted with
Warning indicates a
potentially
maximum operating pressure
of the air tool (90 PSI). The air
tool could explode and result
Caution indicates a
in death or serious personal injury.
potentially
3 . Do not exceed any pressure rating of
4 . Disconnect the air tool from air
Notice indicates
important
and ear protection must be
worn during operation.
5 . Do not wear loose fitting clothing,
You can
create
6 . Do not wear jewelry when operating
7 . Do not depress trigger when
8 . Always use attachments designed
impact quality sockets only. Hand
tool sockets are "glass-hard" and will
shatter and can cause serious personal
injury if used with air tools.
TL140289
with this product
carefully . Be thoroughly
familiar with the controls
and the proper use of the
equipment .
these rules of safe operation should
be allowed to use the air tool .
Do not
exceed
any component in the system .
supply before changing tools or
attachments, servicing and during
non-operation .
Safety
glasses
scarves, or neck ties . Loose clothing
may become caught in moving parts
and result in serious personal injury .
any tool . Jewelry may become
caught in moving parts and result in
serious personal injury .
connecting the air supply hose .
for use with air powered tools .
Do not use damaged or worn
attachments .
Do not use hand
tool sockets. Use
IN738200AV 1/12
MANUAL