Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Description of parts
A Blade set
B Cutting length adjustment lever
C On/off switch
D Mains cable
E Locking switch for cutting length adjustment
F Attachment comb
G Blade guard
H Cleaning brush
I
Oil for blade set
Not shown: optional attachment combs, clippers or hairstyling comb
(depending on model)
Important safety information
For your own protection from injuries and electric shocks, the follow-
ing information must be observed when using electrical equipment:
Read these operating instructions carefully and make sure you
understand them before using the appliance!
·
Only use hair clippers to cut human hair.
Only use animal clippers to cut animal hair and animal fur.
·
Only use the appliance for the proper use as described in the
operating instructions.
·
Keep packaging away from children.
·
This appliance is not suitable for use by people (including children)
with physical, sensory or mental disabilities or who do not have
the relevant experience or knowledge of using such appliance,
unless under the supervision of or after having received instruction
in the use of the appliance by an individual who is responsible for
their safety. Children should be supervised to ensure they do not
play with the appliance.
·
The operating instructions should be retained so that they can be
referred to at a later date and should be passed on to all subse-
quent owners or users of the appliance.
·
Only operate the appliance with an alternating current and with the
voltage stated on the nameplate.
Warning:
·
Do not use the appliance near bath tubs, showers or
other water-filled containers. It should also not be used
in areas of high humidity. Always disconnect from the
mains power supply after use since water can pose a
hazard, even when the appliance is switched off.
·
Never touch electrical equipment that has fallen into
water.
Disconnect from the mains immediately.
·
If the appliance is dropped into water, it may not be
used again subsequently.
·
It is essential to PREVENT electrical equipment from
coming into contact with water or other liquids.
·
Never use the appliance with wet hands or feet.
·
Never use the appliance when barefoot.
·
As additional safety measure, it is recommended that a tested
residual current appliance (RCD) with a residual operating current
of not more than 30 mA be installed in the bathroom circuit. Ask
your electrician for advice.
·
Disconnect from the mains before cleaning or servicing the
appliance.
·
Never use the appliance if it is defective, if it has fallen onto the
floor or if the mains cable is damaged. A damaged mains cable
may only be replaced with an original replacement cable by an
authorised Service Centre or another similarly qualified person, in
order to avoid hazards.
·
Repairs may only be performed at an authorised Service Cen-
tre using original parts. Only specialists properly trained in the
handling of electrotechnical appliances may repair electrical
equipment.
·
Only use accessories recommended by the manufacturer.
·
When disconnecting the appliance from the mains, never pull on
the mains cable or on the appliance itself.
·
Do not hold the appliance by the mains cable to carry it and do
not use the cable as a handle.
·
Do not wind the mains cable around the appliance.
·
Keep the mains cable and appliance away from hot surfaces.
·
Make sure that the mains cable is not twisted or kinked when used
and stored.
·
Never use the appliance where aerosol (spray) products are being
used or where oxygen is released.
·
Do not expose the appliance to temperatures below 0°C and
above +40°C for any length of time. Avoid direct exposure to
sunlight.
·
The appliance is not intended for commercial use.
·
The appliance is safety insulated and radio screened. It meets the
requirements of EU Directive 2004/108/EC regarding electromag-
netic compatibility and EC Low Voltage Directive 2006/95/EC.
·
We are not liable for damage caused as a result of improper use
or failure to observe these operating instructions.
Start-up
·
Oil the blade set (Fig. 5).
·
Connect to the mains power supply.
·
Using the on/off switch, switch on the appliance (Fig. 1ⓐ).
Note for types 1170 and 1400: the audible click that can some-
times be heard when switching on the appliance is a result of the
torque of the alternating current drive unit. This is normal and no
failure of the appliance.
·
Using the on/off switch, switch off the appliance after use
(Fig. 1ⓑ) and disconnect from the mains.
Cutting length adjustment (Type 1170 and Type 1400)
·
Without the attachment comb, the normal cutting length of the
appliance is approx. 0.1 mm.
·
The cutting length can be adjusted between 0.1 and 3 mm, even
when the appliance is in use.
·
Slide down the locking switch (Fig. 2ⓑ)
·
By moving the adjustment lever at the side (Fig. 3ⓐ), it is possible
to set the cutting length at various pre-set positions (MultiClick).
·
Sliding the locking switch upward (Fig. 2ⓐ) unlocks the setting
and restores the normal cutting length of approx. 0.1 mm.
Attaching/removing the attachment comb
·
Slide the attachment comb on to the blade set in the direction of
the arrow until it reaches the limit stop (Fig. 4ⓐ).
·
The attachment comb can be removed by pushing it in the direc-
tion of the arrow (Fig. 4ⓑ).
Cutting with attachment combs (Type 1170 and
Type 1400)
Depending on the model, various attachment combs are included in
the scope of supply. Attachment combs #1 (4.5 mm), #2 (6 mm), #3
(9 mm), #4 (14 mm), #5 (19 mm) and an adjustable attachment comb
(4 - 18 mm) are also optionally available as accessories.
To achieve the desired cutting lengths, the adjustment lever should
not be locked (Fig. 3ⓑ); to this end, slide the locking switch upward
(Fig. 2ⓐ).
Cleaning and Care
·
Do not immerse the appliance in water!
·
After each use, remove the hair clippings from the blade set with
the cleaning brush.
·
Only wipe the appliance with a soft cloth, which may be damp-
ened slightly.
Do not use solvents or abrasives!
·
For a long-lasting, good cutting performance, it is important to oil
the blade set frequently (Fig. 5).
·
If the cutting performance deteriorates after long use despite regu-
lar cleaning and oiling, the blade set should be replaced.
·
Use the blade guard when the appliance is not in use.
·
Always store the appliance with the blade guard in place.
Changing the bottom blade and the top blade
·
Switch off the appliance using the on/off switch (Fig. 1ⓑ).
·
Disconnect from the mains power supply.
·
Undo both screws on the blade set; remove the bottom blade and
the top blade (Fig. 7).
ENGLISH
de
en
fr
it
es
pt
nl
sv
da
fi
tr
pl
cs
sk
hu
hi
ru
uk
el
ar
fa
7
Publicidad
Tabla de contenido
