Haier HUM18HA03/R2(DB) Manual De Instalación
Ocultar thumbs Ver también para HUM18HA03/R2(DB):

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Installation Manual of Room Air Conditioner
Preparation
Necessary Tools for Installation
Driver
Nipper
Hacksaw
Hole core drill
Spanner(17,19 and 26mm)
Gas leakage detector or
soap-and-water solution
Power Source
Before inserting power plug into receptacle, check the voltage without fail.
The power source is the same as the
Install an exclusive branch circuit of the power.
A receptacle shall be set up in a distance where the power cable can be
reached.Do not extend the cable by cutting it.
Drawing for the installation of indoor and outdoor units
The models adopt HFC free refrigerant R410A
more than 5cm
more than
10cm
Arrangement of piping
directions
Rear left
Left
Below
The marks from
to
A
in the figure are the
G
parts numbers.
The distance between
the indoor unit and the
floor should be more
than 2m.
Please be subject to the actual product purchased , the above picture is just for your reference.
Read this manual before installation
Explain sufficiently the operating means to the user according to this manual.
NO.0010531116
All manuals and user guides at all-guides.com
Torque wrench
(17mm,22mm,26mm)
Pipe cutter
Flaring tool
Knife
Measuring tape
Reamer
corresponding name plate.
Rear
right
Right
more than 10cm
more than
60cm
Selection of Installation Place
Indoor Unit
Place, robust not causing vibration, where the body can be supported sufficiently.
Place, not affected by heat or steam generated in the vicinity, where inlet and outlet of the
unit are not disturbed.
Place, possible to drain easily, where piping can be connected with the outdoor unit.
Place, where cold air can be spread in a room entirely.
Place, nearby a power receptacle, with enough space around. (Refer to drawings).
Place where the distance of more than lm from televisions, radios, wireless apparatuses
and fluorescent lamps can be left.
In the case of fixing the remote controller on a wall, place where the indoor unit can
receive signals when the fluorescent
Outdoor Unit
Place, which is less affected by rain or direct sunlight and is sufficiently ventilated.
Place, possible to bear the unit, where vibration and noise are not increased.
Place, where discharged wind and noise do not cause a nuisance to the neighbors.
Place, where a distance marked
Attention must be paid to
the rising up of drain hose
G
more than 10cm
F
A
C
more than
10cm
D
E
more than15cm
lamps in the room are lightened.
is available as illustrated in the above figure.
Optional parts for piping
Non-adhesive tape
A
Adhesive tape
B
Saddle (L.S) with screws
C
Connecting electric cable
D
for indoor and outdoor
E
Drain hose
F
Heating insulating material
Piping hole cover
G
Floor fixing dimensions of the
outdoor unit (Unit:mm)
Fixing of outdoor unit
Fix the unit to concrete or block
with bolts (10mm) and nuts firmly
and horizontally.
When fitting the unit to wall
surface, roof or rooftop, fix
a supporter surely with nails
or wires in consideration of
earthquake and strong wind.
If vibration may affect the
house, fix the unit by attaching a
vibration-proof mat.

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Haier HUM18HA03/R2(DB)

  • Página 1 All manuals and user guides at all-guides.com Installation Manual of Room Air Conditioner Preparation Necessary Tools for Installation Selection of Installation Place Indoor Unit Torque wrench Driver ● ● (17mm,22mm,26mm) Nipper ● ● Place, robust not causing vibration, where the body can be supported sufficiently. Hacksaw Pipe cutter ●...
  • Página 2: Accessory Parts

    All manuals and user guides at all-guides.com 1. Insert the drain hose into the dent of heat insulation materials of indoor unit. Accessory parts 2. Insert the indoor/outdoor electric cable from backside of indoor unit, and pull it out on the front side, then connect them. 3.
  • Página 3: Power Cable

    All manuals and user guides at all-guides.com Outdoor unit Installation of Outdoor Unit Outdoor unit A Drawing for the installation of indoor and outdoor units Install according to Connection of pipes ● To bend a pipe, give the roundness as large as possible not to crush the pipe , 4G0.75mm and the bending radius should be 30 to 40 mm or longer.
  • Página 4: Power Source Installation

    All manuals and user guides at all-guides.com No gas leakage? On Drainage In case of gas leakage, tighten parts of pipe connection. If ● Please install the drain hose so as to be downward slope without fail. leakage stops, then proceed 6. steps Please don’t do the drainage as shown below.
  • Página 5: Preparación

    All manuals and user guides at all-guides.com Manual de instalación de aparato de aire acondicionado Preparación Herramientas necesarias para realizar la instalación Selección del lugar de instalación Unidad interior  Destornillador  Llave dinamométrica (17 mm, 22 mm, 26 mm) ●...
  • Página 6: Unidad Interior

    All manuals and user guides at all-guides.com  En caso de realizar la entubación a través de la parte trasera izquierda, doble los Accesorios tubos de acuerdo con la dirección de entubación que figura en la marca del orificio de entubación trasera izquierda, ubicada sobre los materiales aislantes. 1.
  • Página 7: Unidad Exterior

    All manuals and user guides at all-guides.com Unidad exterior a la unidad interior A Instalación de la unidad exterior Instale la unidad exterior de acuerdo con el diagrama de instalación de unidades interiores y exteriores. 4G0.75mm Conexión de los tubos  Para doblar un tubo, intente hacer la curva lo más suave posible para no aplastar el Unidad interior A tubo. El radio de doblado debe ser de entre 30 y 40mm o superior.
  • Página 8: Etiqueta De Carga De Refrigerante

    All manuals and user guides at all-guides.com Cuchilla de conicidad 1. Cortar el tubo 2. Eliminar las rebabas 4. Abra el vástago de la válvula de 2 vías 90 grados hacia la izquierda. Después de 6 segundos, cierre la válvula de 2 vías e inspeccione si existen fugas de gas. 5. ¿No existen fugas de gas? 4. Tubo cónico 3. Insertar la tuerca cónica En caso de que exista una fuga de gas, apriete las conexiones de los tubos.
  • Página 9 All manuals and user guides at all-guides.com Manuale d’installazione del Condizionatore Preparazione Attrezzi necessari per l’’installazione Selezione del luogo d’installazione Unità interna  Cacciavite  Chiave dinamometrica (17mm, 22mm, 26mm) ● Installare in un luogo solido, senza vibrazioni, in grado di supportare il peso dell’unità. ...
  • Página 10: Parti Accessorie

    All manuals and user guides at all-guides.com  Se la tubatura è posteriore sinistra, piegare i tubi seguendo la direzione delle tuba- Parti accessorie ture verso il contrassegno del foro per la tubatura sinistra posteriore che è stampi- gliato sui materiali d'isolamento termico. 1.
  • Página 11 All manuals and user guides at all-guides.com Unità da esterno Unità da esterno A Installazione dell’unità esterna Installare attenendosi allo schema per l’installazione dell’unità interna ed esterna 4G0.75mm Collegamento dei tubi  Per piegare i tubi, curvarli con un raggio molto ampio per non spaccarli, il raggio deve essere compreso tra 30 e 40 mm o più.
  • Página 12 All manuals and user guides at all-guides.com Corretto Scorretto 4. Aprire la valvola a stelo della valvola a 2 vie girandolo di 90 gradi in senso antiora- rio. Dopo 6 secondi, chiudere la valvola a 2 vie ed eseguire un'ispezione per accer- tarsi che non ci siano perdite di gas. 5. Non ci sono perdite di gas? Inclinato Danno della svasatura Rottura Parziale Troppo esterno Se ci sono perdite di gas, stringere i giunti del tubo. Se la Sullo scarico perdita di arresta, procedere al punto 6.
  • Página 13 All manuals and user guides at all-guides.com Manuel d'installation d'un climatiseur de pièce Préparation Outillage requis pour l'installation Sélection de l'emplacement pour l'installation Unité intérieure  Clé  Clé dynamométrique (17 mm, 22 mm, 26 mm) ● L'emplacement doit être solide sans vibration et offrir un support suffisant. ...
  • Página 14: Unité Intérieure

    All manuals and user guides at all-guides.com  Dans le cas d'une tuyauterie à gauche, découpez, avec une pince, le couvercle Accessoires pour la tuyauterie gauche.  Pour une tuyauterie à l'arrière gauche, cintrez les tuyaux selon le sens de la tuyau- terie jusqu'à...
  • Página 15: Unité Extérieure

    All manuals and user guides at all-guides.com Unité extérieure Unité extérieure A Installation de l’unité extérieure Effectuez l'installation selon le schéma d'installation des unités intérieures et extérieures 4G0.75mm Raccords de tuyauterie  Lorsque vous courbez un tuyau, donnez-lui autant de rondeur que possible afin de Unité intérieure A ne pas l’écraser ; le rayon de courbure doit être d’au moins 30 à 40 mm, voire plus.  Connectez d'abord le côté...
  • Página 16: Etiquette De Charge De Réfrigérant

    All manuals and user guides at all-guides.com Matrice de l'outillage 1.Coupez le tuyau d'évasement 2. Nettoyez les ébavures 4. En tournant dans le sens antihoraire, ouvrez le robinet de la vanne à 2 voies à un angle de 90 degrés. Environ 6 secondes plus tard, fermez la vanne à 2 voies et ins- pectez afin de détecter toute fuite de gaz. 5. Pas de fuite de gaz? 3.Insérez l'écrou 4. Tuyau d'évasement En cas de fuite de gaz, resserrez les pièces de connexion d'évasement du tuyau. Lorsque la fuite est maîtrisée, passez à l'étape 6 Si elle n'a pas été maîtrisée, videz le réfrigérant de l'orifice d'entretien.

Este manual también es adecuado para:

Hum18hb03/r2(db)Hum18hc03/r2(db)

Tabla de contenido