Toshiba RAS-13N3KCV Serie Manual Del Usuario página 4

2 PREPARATION BEFORE USE
Preparing Filters
1. Open the air inlet grille and remove the air filters.
2. Attach the filters. (see detail in the accessory sheet).
Loading Batteries (when use wireless operation.)
1. Remove the slide cover.
2. Insert 2 new batteries (AAA type)
following the (+) and (–) positions.
Clock Setup
1. Push by tip of the pencil.
If timer indication is flashing, go to the next step 2.
2. Press or : adjust the time.
3. Press : Set the time.
Remote Control Reset
Push by tip of the pencil or
1. Remove the batteries.
2. Press .
3. Insert the batteries.
AIR FLOW DIRECTION
3
FIX
Press : Move the louver in the
1
desired vertical direction.
SWING
Press : Swing the air
2
automatically and press again to stop.
3
For horizontal direction, adjust manually.
Note:
• Do not move the louver manually by others.
• The louver may automation positioning by some operation mode.
REMOTE CONTROL
4
1 Infrared signal emitter
2 Start/Stop button
3 Mode select button (MODE)
4 Temperature button (TEMP)
5 Fan speed button (FAN)
6 Swing louver button (SWING)
7 Set louver button (FIX)
8 On timer button (ON)
9 Off timer button (OFF)
! Setup button (SET)
" Clear button (CLR)
# Memory and Preset button (PRESET)
$ One-Touch button (ONE-TOUCH)
% High power button (Hi-POWER)
& Power selection button (POWER-SEL)
( Quiet button (QUIET)
) Comfort sleep button (COMFORT SLEEP)
~ Filter reset button (FILTER)
+ Set clock button (CLOCK)
, Check button (CHECK)
- Reset button (RESET)
Note:
• The provided Remote Controller is a wireless type, which also can be used as
a wire. Please see "How to Connect The Remote Controller for Wired
Operation", located in installation instruction, in case of wired control is required.
• In wire operation, remote controller will return to initial condition (PRESET,
TIMER and CLOCK will return to initial condition) when user shutdown power
supply of Air conditioner.
ONE-TOUCH
5
Press the "ONE-TOUCH" button for fully automated operation that is customized
to the typical consumer preferences in your region of the world. The customized
settings control temperature air flow strength, air flow direction and other settings
to provide you alternate contact with "ONE-TOUCH" of the button. If you prefer
other settings you can select from the many other operating functions of your
Toshiba unit.
ONE-TOUCH
Press : Start the operation.
TSB 1110650185 (01_EN).indd 4 TSB 1110650185 (01_EN).indd 4
To automatically select cooling or fan only operation
10
1
11
#
4
2
6
3
5
SWING FAN
7
(
$
ONE-TOUCH FIX QUIET
12
%
&
POWER-SEL Hi POWER
"
COMFORT
8 9
SLEEP
) !
, -
+ ~
6 AUTOMATIC OPERATION
MODE
1. Press : Select A.
2. Press : Set the desired temperature.
FAN
3. Press : Select AUTO, LOW , LOW+
HIGH .
7 COOLING / FAN ONLY OPERATION
MODE
1. Press : Select Cool or Fan only
2. Press : Set the desired temperature.
Cooling: Min. 17°C, Fan Only: No temperature indication
3. Press FAN : Select AUTO, LOW , LOW+
or HIGH .
DRY OPERATION
8
For dehumidification, a moderate cooling performance is controlled automatically.
MODE
1. Press : Select Dry .
2. Press : Set the desired temperature.
Hi-POWER OPERATION
9
To automatically control room temperature and airflow for faster cooling operation
(except in DRY and FAN ONLY mode)
Press Hi POWER : Start and stop the operation.
POWER-SELECTION OPERATION
This function is used when its circuit breaker is shared with other electrical
appliances. It limits the maximum current/power consumption to 100%, 75%
or 50%. The lower the percentage, the higher the saving and also the longer
the compressor lifetime.
POWER-SEL
:
Press Select (for 100%),
• When the level is selected, PWR-SEL level flashes on LCD display for 3
seconds. In case of 75% and 50% level, number "75" or "50" also flashes
for 2 seconds.
• Due to the reason that POWER SELECT FUNCTION limits the maximum
current, inadequate cooling capacity may occur.
TEMPORARY OPERATION
In case of the misplaced or discharged remote control
• Pressing the RESET button, the unit can start or
stop without using the remote control.
• Operation mode is set on AUTOMATIC operation,
preset temperature is 25°C and fan operation is
automatic speed.
TIMER OPERATION
Set the timer when the air conditioner is operating.
Setting the ON Timer
1
Press : Set the desired ON
timer.
2
Press : Set the timer.
3
Press : Cancel the timer.
Daily timer allows the user to set both the ON & OFF timers and will be
activated on a daily basis.
Setting Everyday Timer
1
Press : Set the ON timer.
2
Press : Set the OFF timer.
• During the every day timer is activating, both arrows ( , ) are indicated.
Note:
• Keep the remote control in accessible transmission to the indoor unit;
otherwise, the time lag of up to 15 minutes will occur.
• The setting will be saved for the next same operation.
, MED , MED+ , or
.
, MED , MED+ ,
(for 75%), (for 50%)
Setting the OFF Timer
Press : Set the desired OFF
timer.
Press : Set the timer.
Press : Cancel the timer.
3
Press .
Press : button during the
4
( or ) mark flashing.
5/30/12 3:17 PM 5/30/12 3:17 PM