Bevel Cut - BAUKER CMS185S Manual De Instrucciones

If possible, always use a clamping device such as a 'G" clamp to secure your
workpiece. When cutting your workpiece, keep your hands well away from the blade
area.
Do not remove a cut-off piece on the right-hand side of the blade using your left hand.
A bevel cut is made by cutting across the grain of the workpiece with the blade angled
to the fence and mitre table. The mitre table is set at the zero degree position and the
blade set at an angle between 0 °and 45 °.
1. Pull on the release knob (4) and lift the saw arm to its full height.
2. Loosen the mitre locks (20) and lifting up the mitre latch (21).
3. Rotate the mitre table (16) until the pointer aligns with zero on the mitre scale (17).
4. Release mitre latch (21) and retighten the mitre locks (20).
5. Loosen the bevel lock (12) and move the saw arm (3) to the left to the desired bevel
angle (between 0 ° and 45 °). Tighten the bevel lock (12).
6. Place the workpiece flat on the table with one edge securely against the fence (14).
If the board is warped, place the convex side against the fence. If the concave side is
placed against the fence, the board could break and jam the blade.
7. When cutting long pieces of timber, support the opposite end of the timber with side
support bars, a roller stand or a work surface that is level with the saw table.
8. Before turning on the saw, perform a dry run of the cutting operation to check that
there are no problems such as a clamp interfering with the cutting action.
9. Hold the operating handle (5) firmly and squeeze the release latch (30). Allow the
blade to reach maximum speed and slowly lower the blade into and through the
workpiece.
10. Release the switch trigger (19) and allow the saw blade to stop rotating before
raising the blade out of the workpiece. Wait until the blade stops before removing the
workpiece.
1. For cutting safety always use two attach fence.
2. If use bevel cut , drag out the attach fence.
The attach fence distance moving parts about 3 mm - 8mm at any times.
23

Bevel cut

Attach fence
Compound mitre cut
If possible, always use a clamping device such as a 'G" clamp to secure your
workpiece. When cutting your workpiece, keep your hands well away from the blade
area.
Do not remove a cut-off piece on the right-hand side of the blade using your left hand.
A compound mitre cut involves using a mitre angle and a bevel angle at the same time.
It is used in making picture frames, to cut mouldings, making boxes with sloping sides
and for roof framing. Always make a test cut on a piece of scrap wood before cutting
into the good material.
1. Pull on the release knob (4) and lift the saw arm to its full height.
2. Loosen the mitre locks (20) and lifting up the mitre latch (21) ..
3. Rotate the mitre table (16) until the pointer aligns with the desired angle on the mitre
scale (17).
4. Release mitre latch (21) and retighten the mitre locks (20).
5. Loosen the bevel lock (12) and move the saw arm (3) to the left to the desired bevel
angle (between 0°and 45°). Tighten the bevel lock (12).
6. Place the workpiece flat on the table with one edge securely against the fence (14).
If the board is warped, place the convex side against the fence. If the concave side is
placed against the fence, the board could break and jam the blade.
7. When cutting long pieces of timber, support the opposite end of the timber with the
side support bars, a roller stand or a work surface that is level with the saw table.
8. Before turning on the saw, perform a dry run of the cutting operation to check that
there are no problems such as a clamp interfering with the cutting action.
9. Hold the operating handle (5) and firmly and squeeze the release latch (30). Allow the
blade to reach maximum speed and slowly lower the blade into and
through the workpiece.
10. Release the switch trigger (19) and allow the saw blade to stop rotating before
raising the blade out of the workpiece. Wait until the blade stops before removing the
workpiece.
To slide cut wide boards
To slide cut wide boards, Unlock the slide lock knob (24) and allow the cutting head
assembly to move freely.
24