Black and Decker Powerful Solutions AS36LN Traducción De Las Instrucciones Originales página 9

LED light
The LED light (5) is activated automatically when the trigger is
depressed. The LED will also illuminate when the trigger is
depressed and the forward/reverse slider (2) is in the locked
off position (central position).
Hints for optimum use
Screwdriving
Always use the correct type and size of screwdriver bit.
u
If screws are difficult to tighten, try applying a small
u
amount of washing liquid or soap as a lubricant.
Use the spindle lock to loosen very tight screws or to
u
firmly tighten screws.
Always hold the tool and screwdriver bit in a straight line
u
with the screw.
When screwing in wood, it is recommended to drill a pilot
u
hole with a depth equal to the length of the screw. A pilot
hole guides the screw and prevents splintering or
distortion of the wood. For the optimum size of the pilot
hole, refer to the table below.
When screwing in hardwood, also drill a clearance hole
u
with a depth equal to half the length of the screw. For the
optimum size of the clearance hole, refer to the table
below.
Screw size Pilot hole ø
(softwood)
No. 6 (3.5 mm) 2.0 mm
No. 8 (4 mm) 2.5 mm
No. 10 (5 mm) 3.0 mm
Drilling
Always apply a light pressure in a straight line with the drill
u
bit.
Just before the drill tip breaks through the other side of the
u
workpiece, decrease pressure on the tool.
Use a block of wood to back up workpieces that may
u
splinter.
Make an indentation using a centre punch at the centre of
u
the hole to be drilled in order to improve accuracy.
Drilling using a countersink drill bit (fig. G1 - G3)
The countersink drill bit (12) is used to remove material to seat
the screw head flush to the surface.
Warning! Always gear the diameter of the drill bit to the
diameter of the screw.
Place the drill bit into the tool.
u
Drive the drill into the material (fig. G1).
u
Pilot hole ø Clearance
(hardwood) hole
2.5 mm 3.6 mm
3.0 mm 4.5 mm
3.5 mm 5.0 mm
Drive the cutter on the drill bit as far into the material as
u
necessary. Cut away sufficient material to sink the screw
head into the material (fig. G2).
Drive the screw into the material with a screwdriver bit
u
(fig. G3).
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the
performance of your tool. By using these accessories you will
get the very best from your tool.
This tool uses screwdriver bits with a 1/4" (6.35 mm)
hexagonal shank. Piranha Super-lok accessories are
designed for use with this tool.
Maintenance
Your Black & Decker corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
u
Do not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
u
from the interior (when fitted).
Protecting the environment
Z
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
ENGLISH
9