Bosch AdvancedGrind 18 Manual Original página 20

OBJ_BUCH-2850-001.book Page 20 Friday, September 9, 2016 1:05 PM
20 | English
Technical Data
Angle Grinder
Article number
Rated voltage V=
-1
Rated speed min
Speed control adjust-
-1
ment min
Grinding disc diameter,
max. mm
Thread of grinder
spindle
Thread length (max.) of
grinder spindle mm
Constant electronic
control
Speed preselection
Soft starting
Restarting Protection
Overload Protection
Weight according to
EPTA-Procedure
01:2014
– with vibration-damp-
ing auxiliary handle kg
– with standard-auxil-
iary handle kg
Permitted ambient
temperature
– during charging °C
**
– during operation
and during storage °C
Recommended
batteries
Recommended
chargers
– for PBA 18V ...W–B,
PBA 18V ...W–C
– for PBA 18V ...V–.
* depending on the battery pack being used
** limited performance at temperatures <0 °C
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise levels of the product are:
Sound pressure level 80 dB(A); Sound power level 91 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3:
2
Surface grinding: a =6.5 m/s , K=1.5 m/s
h
2
Disk sanding: a =5.0 m/s , K=1.5 m/s
h
1 609 92A 2LJ | (9.9.16)
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
AdvancedGrind 18
EN 60745 and may be used to compare one tool with anoth-
3 603 CD3 1..
er. It may be used for a preliminary assessment of exposure.
18 The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
10000
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
2800 – 10000
may significantly increase the exposure level over the total
working period.
125
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
M 14
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
22
period.
Identify additional safety measures to protect the operator

from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-

terns.


Assembly

Battery Charging
 Use only the chargers listed in the technical data. Only
*
2.7 (2.5 Ah)–3.2 (6.0 Ah)
Note: The battery supplied is partially charged. To ensure full
*
2.4 (2.5 Ah)–3.0 (6.0 Ah) capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
0...+45
ducing its service life. Interrupting the charging procedure
does not damage the battery.
–20...+50
The lithium-ion battery is protected against deep discharging
PBA 18V ...W–B
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
PBA 18V ...W–C
circuit: The inserted tool no longer rotates.
PBA 18V ...V–.
 Do not continue to press the On/Off switch after the
AL 18.. CV
Observe the notes for disposal.
Removing the battery
AL 22.. CV
AL 18.. CV
To remove the battery 5, press the battery unlocking button 6
and pull the battery upward out of the power tool. Do not ex-
ert any force.
2
,
2
.
these chargers are matched to the lithium-ion battery of
your power tool.
machine has been automatically switched off. The bat-
tery can be damaged.
Bosch Power Tools