Thomashilfen RECARO Monza Reha Instrucciones De Montaje Y Uso página 7

RECARO Monza Reha – Instructions for assembly and use (supplement)
Contact a Child Passenger Safety (CPS) technician.
You can find a CPS technician in your area at www.nhtsa.dot.gov. Click on "Child Passenger Safety" and select "Certified Child Passenger Safety Technician Locator."
Attend a car seat check-up in your area.
More information about car seat check-ups is available at www.nhtsa.dot.gov under "Child Seat Inspections" or at www.seatcheck.org. You can also call 1-855-SEAT-
CHECK to find the next or closest seat check event.
Purpose / indication
The children car seat RECARO Monza Reha / Monza Seatfix Reha is designed for the transport of children with special needs in vehicles. The clinical pictures are
amongst others:
• cerebral palsy
• hypotony syndrome of unspecific genesis
• muscular dystrophy
• different syndrome diseases
The car seat is characterized by its shell design and pad system, which provide for additional seating safety, stabilization of head and pelvis, and support/control of the
feet.
Thus, the RECARO Monza Reha / Monza Seatfix Reha meets the needs of disabled children very well.
Application risks / contraindications
No application risks / contraindications are known.
5-point positioning belt
Please note: The 5-point positioning belt helps positioning the child in the car seat and does not protect the child in the event of an accident. The 3-point belt in the car
must always be used to secure the child in the seat.
Adjusting the belt length: Pull the loose belt straps to shorten and tighten the belts. To lengthen the belts, tilt the black buckle slightly upwards and pull the belt to the
desired length.
If required, the belt length can also be adjusted with the two belt loops (bolted) at the back of the seat.
Belt buckle: Press the red dent of the buckle to open. Separate the two upper belt fasteners. To close the belt, put the belt fasteners into the buckle and push together until
they lock in place with an audible „Click".
The cover for the crotch pad (zipper) can be removed and washed in the machine at up to 30° C / 86° F. Please undo the zip on the bottom crotch pad as well to remove
the cover.
Fig. 1a: Adjusting the belt length
Headrest (accessory)
Adjust the seat's headrest to the highest position to facilitate attaching the headrest. Pull the covers of the supports over the side parts of the headrest and fasten them at
the top with the press button. The pads are fastened to the lower part of the headrest with an elastic rubber band.
The cover can be removed (zipper) and washed in the machine at up to
30° C / 86° F.
Fig. 2a: Attaching the headrest
* Set of removable head supports, lateral trunk supports and lateral seat supports
Lateral trunk supports (accessory)
The lateral trunk supports can be fastened at 3 different heights on the left and right in the back area with press buttons and Velcro. Start with the press buttons.
The supports can be fixed more firmly by pressing against the fleece strips in the back of the seat.
The cover can be removed (zipper) and washed in the machine at up to 30° C / 86° F.
Fig. 3a: Press button
* Set of removable head supports, lateral trunk supports and lateral seat supports
Lateral seat supports (accessory)
Adjust the backrest to a horizontal position to facilitate attachment of the lateral supports. Pull the covers of the lateral supports over the side parts of the seat surface and
attach them to the rear of the seat surface with the press button.
The cover can be removed (zipper) and washed in the machine at up to 30° C / 86° F.
Fig. 4a: Attaching the support
* Set of removable head supports, lateral trunk supports and seat supports
Abduction block (accessory)
Before attaching the abduction block loosen the Allen screw on the front of the seat (holds the 5-point positioning belt, too) and remove the bottom strap of the 5-point
positioning belt.
The depth adjustment is adjusted with two Allen screws on a rail underneath the abduction block. Before final assembly you should adapt the depth adjustment to the leg
length child.
Insert the metal retainer of the abduction block into the provided slot underneath the foam padding of the seat and hook into place. The borehole and thread must lie
above one another. Remember to re-attach the 5-point positioning belt before tightening the abduction block.
Note: When tightening the abduction block, make sure to bolt the screw lightly only, to avoid overwinding of the rivet nut.
To mount the abduction block you will need the 3 mm / 0.1" Allen key provided.
The cover can be removed (cord) and washed in the machine at up to 30° C / 86° F.
Fig. 5a: Attaching the abduction block
All manuals and user guides at all-guides.com
Fig. 1b: Opening and closing the belt buckle („Click")
Fig. 2b: Fastening at bottom (a) and top (b)
Fig. 3b: Velcro-fastening
Fig. 4b: Press button, rear
Fig. 5b: Depth adjustment
item code: 845*
item code: 845*
item code: 845*
item code: 807
7