Makita DSC251 Manual De Instrucciones página 8

During operation
11. Do not use the Tipped Saw for any purpose other
than cutting. Do not subject the blades to damage
or stress. It can break the blades resulting in seri-
ous personal injury.
12. Hold the material firmly, in a vice or similar, so
that it cannot move when cutting. If the material
moves, the operation becomes unstable and
cannot be controlled, resulting in damage to the
blades and possible serious personal injury.
13. Start cutting only after the Tipped Saw has
reached maximum speed. If the Tipped Saw is set
against the material before the motor is started,
the blades will be overloaded and damaged,
resulting in possible serious personal injury.
14. Do not cut in zigzags, curves, diagonals, or use
the side of the blade to prise or for any other
purpose.
15. If during cutting, there is an abnormal sound,
abnormal vibration, or if the cutting parts are badly
worn, stop operation.
Continuing the operation under such conditions
will damage the Tipped Saw blades with the result
that chips may be ejected causing serious per-
sonal injury.
16. Continuous operation makes the Tipped Saw
blades hot and reduces the cutting performances.
Maintenance
17. If there is deformation, a crack or damage on the
Tipped Saw, stop the operation. Continuing the
operation under such conditions will further dam-
age the Tipped Saw which may break up. Ejected
broken parts can cause serious personal injury.
18. Only keep and use Tipped Saws that are in good
condition and the blades sharp and clean.
WARNING:
Always wear protective equip-
ment; safety glasses, safety shoes, dust mask
and helmet.
WARNING:
Use only Makita supplied Tipped
Saw. Using non Makita parts may damage the tool
and can result in serious accident or injury.
Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
Do not disassemble or tamper the battery
2.
cartridge. It may result in a fire, excessive heat,
or explosion.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
If electrolyte gets into your eyes, rinse them
4.
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any con-
ductive material.
Avoid storing battery cartridge in a con-
(2)
tainer with other metal objects such as
nails, coins, etc.
Do not expose battery cartridge to water
(3)
or rain.
A battery short can cause a large current
flow, overheating, possible burns and even a
breakdown.
6. Do not store and use the tool and battery car-
tridge in locations where the temperature may
reach or exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
8. Do not nail, cut, crush, throw, drop the battery
cartridge, or hit against a hard object to the
battery cartridge. Such conduct may result in a
fire, excessive heat, or explosion.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
For commercial transports e.g. by third parties,
forwarding agents, special requirement on packa-
ging and labeling must be observed.
For preparation of the item being shipped, consul-
ting an expert for hazardous material is required.
Please also observe possibly more detailed natio-
nal regulations.
Tape or mask off open contacts and pack up the
battery in such a manner that it cannot move
around in the packaging.
11. When disposing the battery cartridge, remove
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
12. Use the batteries only with the products spe-
cified by Makita. Installing the batteries to non-
compliant products may result in a fire, excessive
heat, explosion, or leak of electrolyte.
13. If the tool is not used for a long period of time,
the battery must be removed from the tool.
14. During and after use, the battery cartridge may
take on heat which can cause burns or low
temperature burns. Pay attention to the han-
dling of hot battery cartridges.
15. Do not touch the terminal of the tool imme-
diately after use as it may get hot enough to
cause burns.
16. Do not allow chips, dust, or soil stuck into the
terminals, holes, and grooves of the battery
cartridge. It may result in poor performance or
breakdown of the tool or battery cartridge.
17. Unless the tool supports the use near high-
voltage electrical power lines, do not use the
battery cartridge near a high-voltage electrical
power lines. It may result in a malfunction or
breakdown of the tool or battery cartridge.
18. Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
8 ENGLISH