First Aid; Additional Safety Instructions; Parts Description - Makita EM407MP Manual De Instrucciones Original

Maintenance
Have your machine serviced by our authorized
1.
service center using only identical replace-
ment parts. Use only identical spare parts and
accessories supplied by MAKITA. Incorrect
repair and poor maintenance can shorten the life
of the machine and increase the risk of accidents.
2. Never alter or remove any components of the
machine. It may cause fire and/or serious injury.
3. After use, clean the machine and check all
screws and nuts for tightness.
Check the condition of the cutting tool, cutting
4.
tool guard and shoulder harness. The cutting
blade must be sharp. Never straighten or weld
damaged cutting tools.
Other instructions
1. Always store the machine in locked rooms and
with an emptied fuel tank.
2. Pay attention to the environment. Avoid unnec-
essary throttle operation for less pollution
and noise emissions. Adjust the carburetor
correctly.
3. Do not operate the engine with faulty exhaust
muffler.

First Aid

1. In case of accident make sure that a first-aid
box is available in the vicinity of the cutting
operations. Immediately replace any item
taken from the first aid box.
2. When asking for help, give the following
information:
— Place of accident
What happened
—
— Number of injured persons
— Kind of injuries
Your name
—

Additional safety instructions

Only use the dedicated cutting blade for
1.
Rotary Scissors Attachment.
Only use the cutting tools that are marked with
2.
a speed equal or higher than the speed marked
on the machine.
Inspect and maintain the machine regularly,
3.
especially before/after use. Have the machine
repaired only by our authorized service center.

PARTS DESCRIPTION

► Fig.3
1 Cap
5 Gear case access bolt
9 Holder (for lower blade)
13 Hex wrench
2 Pipe
6 Holder (for upper blade)
10 Clamp washer
14 Box wrench
4. Before operation, make sure that the shoulder
harness is properly attached to the hanger on
the machine.
5. Remove any adjusting key or wrench before
turning the machine on. An accessory left
attached to a rotating part may result in personal
injury.
6. Be sure to remove the cover on the cutting
blade before operation.
7. Make sure there are no electrical cables, water
pipes, gas pipes etc. that could cause a hazard
if damaged by use of the machine.
8. Do not operate the machine in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases or dust. Machine create sparks
which may ignite the dust or fumes.
9. Do not use the machine in damp or wet loca-
tions or expose it to rain. Water entering the
machine will increase the risk of electric shock,
fire, and malfunction.
10. Do not use the machine on steep slopes and
slippery surface.
11. To avoid accident, leave more than 15m (50
ft) distance between operators when two or
more operators work in one area. Also, arrange
a person to observe the distance between
operators. If someone or an animal enter the
working area, immediately stop the operation.
12. Do not touch the gear case during and imme-
diately after the operation. The gear case
becomes hot during operation and can cause burn
injury.
13. Keep fingers away from switch trigger when
not operating the machine and when moving
from one operating position to another.
WARNING:
dust containing chemicals which may cause
respiratory or other illnesses. Some examples of
these chemicals are compounds found in pesti-
cides, insecticides, fertilizers and herbicides.
Your risk from these exposures varies, depend-
ing on how often you do this type of work. To
reduce your exposure to these chemicals: work
in a well ventilated area, and work with approved
safety equipment, such as those dust masks that
are specially designed to filter out microscopic
particles.
SAVE THESE INSTRUCTIONS.
3 Gear case
7 Upper blade
11 Bolt
- -
12 ENGLISH
Use of this product can create
4 Protector
8 Lower blade
12 Blade cover
- -