Publicidad
Enlaces rápidos
Front Bumper • Pare-choc avant
Voorbumper • Vordere Stoßstange
Paraurti anteriore • Parachoques delantero
KIT1810790
Tools needed:
• 5mm hex key
• Standard socket set
• Standard wrench set
Benötigtes Werkzeug:
• 5mm Inbusschlüssel
• Standard-Steckdosen-Set
• Standardschlüsselsatz
If you require any assistance with these instructions, please call Pride Technical Service at 1-877-800-1248.
Canada providers, phone 1-888-570-1113.
Si vous avez besoin d'aide avec ces instructions, veuillez contacter l'assistance à la clientèle de Pride au
1-888-570-1113.
Indien u hulp nodig hebt bij deze instructies, kunt u contact opnemen met de Technische Dienst van Pride.
Falls Sie Hilfe zu diesen Anweisungen benötigen, kontaktieren Sie bitte den Kundendienst von Pride.
Per assistenza sulle presenti istruzioni contattare il servizio tecnico Pride presso il vostro rivenditore autorizzato.
Si precisa asistencia con estas instrucciones, llame al Servicio técnico de Pride.
Technical Instructions • Instructions techniques
Technische aanwijzingen • Technische Hinweise
Istruzioni tecniche • Instrucciones técnicas
Outils necessaires:
• Clé hexagonale de 5mm
• Ensemble de prise standard
• Jeux de douille standard
• Utensili necessari:
• Chiave esagonale da 5mm
• Set di prese standard
• Set di chiavi standard
www.pridemobility.com
Document Information: Rev A/October 2019
Contents • Contenu • Inhoud
Inhalt • Contenuto • Contenido
A
B
5
NUTNYLK1019
D
1
SCRHHCS1252
F
4
WASLOCK1046
H
2
HDW145163
Benodigd gereedschap:
• 5mm inbussleutel
• Standaard stopcontactenset
• Standaard moersleutel set
Herramientas necesarias:
• Llave hexagonal de 5 mm
• Conjunto de socket estándar
• Juego de llaves estándar
1
BMP8110005
C
6
WASMETR1033
E
4
SCRSHCS1084
G
1
MEC145187
I
2
WASLOCK1016
Publicidad
Manuales relacionados para Pride Mobility KIT1810790
Resumen de contenidos para Pride Mobility KIT1810790
- Página 1 WASMETR1033 SCRHHCS1252 SCRSHCS1084 WASLOCK1046 MEC145187 Front Bumper • Pare-choc avant Voorbumper • Vordere Stoßstange Paraurti anteriore • Parachoques delantero KIT1810790 HDW145163 WASLOCK1016 Tools needed: Outils necessaires: Benodigd gereedschap: • 5mm hex key • Clé hexagonale de 5mm • 5mm inbussleutel •...
- Página 2 Ensure that your scooter is turned off and in drive mode. Use a wrench to remove the bolt (A) from the tire (E). Remove the bolt (A), washer (B), nut (C), bearing spacers (D), and the tire (E) from the frame, and set all aside for later reinstallation.
- Página 3 To install your scooter front bumper: Remove the scooter's batteries, then tilt your scooter so that it is standing upright. Align the front bumper (A) onto the frame as shown. Install the screw (D) and a washer (C) into the bracket at the bottom of the frame, tightening until the screw (D) enters through the other side of the bracket.
- Página 4 Install the four bolts (E) and small lock washers (F) into the sides of the bumper and scooter frame, starting from the inside of the frame as shown until the bolts exit through the outer side of the frame. Install four washers (C) and nuts (B) and tighten.