Fuel And Chain Oil - MADER KM0403580M Manual De Instrucciones

Tabla de contenido

Publicidad

4.Fuel and Chain Oil

FUEL
WARNING
Gasoline is very flammable.Avoid smoking or bringing
any flame or sparks near fuel.Make sure to stop the engine
and allow it cool before refueling and move at least
3m(10ft)away from the fueling point before starting the
engine .
Mix a regular gasoline (leaded or
unleaded,alcohol-free)and a quality-proven motor oil for air
cooled 2 cycle engines.
Do not use BIA or Tcw (2-stroke water-cooling
type)mixed oil.
█RECOMMENDED MIXING RATIO
GASOLINE 25:OIL 1
Exhause emission are controlled by the fundamental
engine parameters and components (eq.,carburetion,ignition
timing and port timing )without addition of any major
hardware or the introduction of an inert material during
combustion.
There engines are certified to operate on unleaded
gasoline .
Make sure to use gasoline with a minimum octane number
of 89RON(USA/Canada:87AL).
If you use a gasoline of a lower octane value than
prescribed,there is a danger that the engine temperature
may rise and an engine problem such as piston seizing may
consequently occur.
Unleaded gasoline is recommended to reduce the
contamination of the air for the sake of your health and the
environment.
Poor quality gasoline or oils may damage sealing
rings,fuel lines or fuel tank of the engine.
▉HOW TO MIX FUEL
Pay attention to agiation.
1.Measure out the quantities of gasoline and oil to be
mixed.
2.Put some of the gasoline into a clean ,approved fuel
container.
3.Pour in all of the oil and agitate well.
4.
Pour in the rest of gasoline and agitate again for at least
one minute.As some oils may be difficult to agitate
depending on oil ingredients,sufficient agitationis
necessary for the engine to last long .Be careful that ,if
the agitation is insufficient ,there is an increased danger
of early piston seizing due to abnormally lean mixture.
5.
Put a clear indication on the outside of the container to
avoid mixing up with gasoline or other containers.
6.
Indicate the contents on outside of container for easy
identification.
FUELING THE UNIT
1.
Untwist and remove the fuel cap.Rest the cap on a
dustless place.
2.
Put fuel into the fuel tank to 80% of the fullcapacity.
3.
Fasten the fuel cap securely and wipe up any fuel
spillage around the unit .
WARNING
1.
Select bare ground for fueling .
2.
Move at least 10 feet (3 meters)away from the fueling
point before starting the engine.
3.
Stop the engine before refueling the unit.At that
time ,be sure to sufficiently agitate the mixed gasoline
in the container.
FOR YOUR ENGINE LIFE,AVOID:
1.
FUEL WITH NO OIL (RAW GASOLINE )-It will
cause severe damage
very quickly.
2.
GASOLINE –It can cause deterioration of rubber and
/or plastic parts and disruption of engine lubrication
3.
OIL FOR4-CYCLE ENGINE USE-It can cause spark
plug fouling ,exhaust port blocking ,or piston ring
sticking .
4.
Mixed fuels which have been left unused for a period
of one month or more may clog the carburetor and
result in the engine failing to operate properly.
5.
In the case of storing the product for a long period of
time ,clean the fuel tank after rendering it empty the
carburetor of the composite fuel.
6.
In the case of scrapping the used mixed oil
container,scrap it only at an authorized repository site .
Note;As for details of quality assurance,read the
description
in
the
carefully.Moreover,normal wear and change in product
with no functional influence are not covered
by the warranty.Also,be careful that,if the usage in the
instruction manual is not observed as to the mixed
gasoline,etc.described therein,it may not be covered by
the warranty.
CHAIN OIL
Use motor oil SAE #10W-30 all year round or SAE #30~#40
in summer and SAE #20 in winter.
Note:Do not use wasted or regenerated oil that can cause
damage to the oil pump.
to the internal
engine parts
section
Limited
Warranty

Publicidad

Tabla de contenido
loading

Tabla de contenido