Ryobi FVM51 Manual Del Operador página 9

LED LIGHT FUNCTIONS
See Figure 1, page 13.
When a charged battery pack is installed in the tool, the LED
light will indicate the status of the battery when the tool is
powered on.
BATTERY STATUS
Normal
Battery Level < 25%
Low Battery
Excessive Force
Over Temperature
OVERLOAD PROTECTION
When the tool is forced or the motor is overloaded, the tool
will automatically shut off. To reset the tool, wait 5 seconds,
slide the on/off switch to the OFF position and then slide it
to the ON position to resume operation. If the tool still does
not resume operation, remove and reinsert the battery. Do
not force the tool.
HIGH TEMPERATURE PROTECTION
This tool is equipped with a high temperature protection
feature that automatically deactivates the tool when it is
overheated. To resume operation, allow the tool to cool and
then turn the tool on.
QUICK-CHANGE COLLET
See Figures 2 - 3, page 13 .
NOTE: The tool ships with a preinstalled collet that is
machined to precision tolerances to fit accessories with
1/8 in. diameter shanks. When installed, the quick change
collet allows the user to change accessories without tools
and without removing the collet from the shaft. The quick
change collet is not compatible with 1/16 in. shanks.
To remove/install the quick change collet:
 Remove the battery pack from the tool.
 Depress and hold the spindle lock button and rotate the
shaft by hand until the spindle lock engages the shaft,
preventing further rotation.
 With the spindle lock engaged, place the included 3/8 in.
wrench on the bottom threaded end of the quick-change
collet and turn counterclockwise to loosen. Continue
turning counterclockwise to remove the collet from the
tool.
 Remove the quick-change collet.
 To install, engage the spindle lock. Place the quick-
change collet on the shaft and begin threading on by
hand until there is resistance. Then use the included 3/8
in. wrench on the bottom threaded end of the collet and
rotate clockwise until tightly secured.
OPERATION
LED LIGHT SCENARIO
Solid Green (No Flashes)
Solid Red (No Flashes)
Flashing Red (3 Flashes)
Flashing Red (6 Flashes)
Flashing Red (9 Flashes)
9 - English
WARNING:
Always use the collet which matches the shank size of the
accessory you plan to use. Never force a large diameter
shank into a collet. The accessory should fit smoothly
into the collet, but you should be able to tighten the ac-
cessory firmly and securely with the quick-change collet.
INSTALLING/REMOVING ACCESSORIES
See Figures 2 - 3, pages 13 .
To install:
 Remove the battery pack from the tool.
 Choose an accessory that fits the collet and is suitable
for the application you are attempting.
 Ensure the quick-change collet is securely installed on
the shaft.
 While depressing the spindle lock, use your hand to
loosen the collet by rotating the sleeve counterclockwise.
 Insert the shank of the accessory into the collet until the
shank bottoms out, then pull it out 1/16 in. to allow for
expansion when the accessory gets hot.
 Rotate the collet sleeve clockwise until clicking stops and
the accessory shank is gripped by the collet.
NOTE: If sleeve cannot be tightened or loosened
sufficiently by hand, use the included 3/8 in. collet wrench
on the top hexed area of the collet. Turn clockwise to
tighten or counterclockwise to loosen.
To remove:
 Remove the battery pack from the tool.
 Loosen the collet sleeve.
 Remove the accessory.
NOTE: When trying to remove an accessory, if the quick-
change collet begins to unthread from the tool, repeat the
install process.
DANGER:
If you are changing an accessory immediately after use,
be careful not to touch the collet or the accessory with
your hands or fingers. You will get burned because of
the heat build-up from operation. Always use the wrench
provided or allow the collet to cool.