Publicidad
Idiomas disponibles
Idiomas disponibles
INSTRUCTIONS FOR USE
SIDE BROOM HEIGHT ADJUSTMENT
NOTE:
Brooms with harder or softer bristles are
available. This procedure is applicable to
each type of broom.
1.
Check the correct height of the side broom from the
ground, by proceeding as follows:
2.
With the machine on level ground, lower the side
broom by disengaging the side broom latch (2, Fig.
C).
3.
Keep the machine stationary and allow the side
broom to rotate for a few seconds.
4.
Stop the side broom and move the machine.
5.
Check that the side broom pattern is as shown in
figure J. If it is different, adjust the broom height as
described in the following step.
6.
Rotate the knob (12, Fig. C) clockwise or
counter-clockwise to adjust the broom height from
the ground.
7.
Perform steps from 1 to 5 again to check the proper
adjustment of the side broom height from the ground.
8.
When the broom becomes too worn, adjustment is
no longer possible. Replace the broom following the
instructions in the following paragraph.
SIDE BROOM REPLACEMENT
NOTE:
Brooms with harder or softer bristles are
available. This procedure is applicable to
each type of brooms.
CAUTION!
It is advisable to use protective gloves when
replacing the main or side broom because
there can be potentially harmful debris
between the bristles.
1.
With the machine on level ground, activate the brake
(26, Fig. C) (if equipped) or block the wheels.
2.
Turn the ignition key (2, Fig. B) to the "0" position.
3.
Slide your hand under the side broom and press the
two tabs (1, Fig. K) inward and then push the broom
(2, Fig. K) downward to disengage it from the four
pins (3, Fig. K) on the side broom hub.
4.
Install the new broom on the machine by aligning it on
the pins (3, Fig. K) and then pressing it onto the two
tabs (1, Fig. K).
5.
Carry out the Side Broom Height Adjustment as
described in the previous paragraph.
10
All manuals and user guides at all-guides.com
DUST FILTER CLEANING AND INTEGRITY
CHECK
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. Install in the reverse order of removal.
NOTE:
Besides the standard paper filter, optional
polyester filters are available. The following
procedure is applicable to each type of filter.
With the machine on level ground, activate the brake
pedal (26, Fig. C) (if present), or block the wheels.
Turn the ignition key (2, Fig. B) to the "0" position.
Disengage the hopper latch (18, Fig. C).
Using the handle (19, Fig. C) remove the hopper (17,
Fig. C) from the machine.
Rotate the filter clamp (1, Fig. L) upward
(approximately 90°) and let the top of the filter frame
(2) rotate outward.
Pull the dust filter (3, Fig. L) upward to remove it.
In a well-ventilated, outdoor area, clean the filter by
gently tapping the side of the filter (1, Fig. M),
opposite to the wire screen (2) on the ground.
Finish cleaning the filter by using compressed air (3,
Fig. M) of max. 6 bars (87 psi), blowing only from the
side protected by the wire screen (2, Fig. M).
According to the type of filter, take care of the
following cautions:
– Paper filter (standard): do not use water or
detergents to clean it; the filter can be damaged.
– Polyester filter (optional): to clean it, follow the
instructions mentioned in number 7 above. For
better cleaning, wash the filter with water and
non-foaming detergents. This type of washing will
clean the filter better, but it reduces the life of the
filter. The use of inadequate detergents can
damage the filter. Check the filtering medium body
for cuts or holes.
If necessary clean the filter compartment rubber seal
(4, Fig. L) along its perimeter and check its integrity.
If necessary replace it.
NOTE:
Reinstall the filter with the wire screen (2,
Fig. M) facing the front part of the machine
(toward the fan (16, Fig. U)).
Blue 32 – 146 2301 000(1)2005-03
Publicidad
Capítulos
