HammerSmith MultiTool M22606 Instrucciones De Uso página 15

• Before sanding, make sure that any nails, screws or
other metal objects protruding from the workpiece
have been removed.
• Always inspect walls and ceilings before drilling and
screwing to avoid damage to potentially concealed
power cables and pipes.
• Use screw clamps or other suitable clamping devices
to fix the workpiece firmly to the surface and to
prevent it from slipping.
• Only use attachments that are supplied for the
Hammersmith MultiTool.
• Do not use broken, damaged or worn accessories or
attachments. Only use attachments that are in good
working condition.
• Always start the device in a suitable space, and allow
it to reach the optimum speed before introducing it to
the workpiece.
• Always remove the battery pack from the device
before changing attachments.
• Keep your hands out of the work area, and always cut
away from yourself and other people.
CHARGING, INSERTING AND REMOVING THE
BATTERY PACK (see Figure 4/A-C)
The quick-charge battery station is designed in
such a way that the battery set can be charged
within an hour, although this depends on the
respective battery set.
1. Plug the charger into a suitable socket before
inserting the battery pack.
2. Insert the battery pack into the charger.
3. A red light indicates that the battery pack is
being charged.
4. A green light indicates that the charging process
is complete. The battery pack is now fully
charged, and can be used or left on the charger.
Charge the battery set immediately after use to avoid
shortening the service life of the battery. In order to
extend the service life, make sure that the battery pack
is never completely empty. We recommend charging
the battery pack after each use. (see Figure 5)
If you want to know how much battery capacity
remains in the battery pack during use, press the
M22606_HammersmithMultitool_Manual_A5_20220126_TC_V02.indd 15 M22606_HammersmithMultitool_Manual_A5_20220126_TC_V02.indd 15
battery level indicator button. (see Figure 6)
LEAVING THE BATTERY PACK CONNECTED TO
THE CHARGER
The battery can be left in the charger; in this case
the LED display is lit green continuously. The charger
keeps the battery pack in a fully charged state.
INSTALLATION AND REMOVAL OF THE BATTERY
PACK IN/FROM THE DEVICE
WARNING: Make sure that the rotational
direction switch is in the middle position to
avoid triggering the switch while removing
or installing the battery pack.
INSTALLATION
Slide the battery pack into the device until it clicks
into place. Make sure that the battery pack is correctly
positioned and fully engaged. (see Figure 7/A+B)
REMOVAL
Press the battery pack release button and pull the
battery out of the device.
ATTACHING THE TOOLS
WARNING: TO AVOID THE RISK OF INJURY,
REMOVE THE BATTERY PACK FROM THE
TOOL BEFORE MAKING ANY
ADJUSTMENTS, REMOVING AN ATTACHMENT OR
INSTALLING A NEW ACCESSORY.
Make sure that the lower edge of the respective
tool attachment and power section of the base
device are aligned horizontally and then push the
attachment into the device until it clicks into place.
(see Figure 8/A-C)
REMOVING THE TOOLS
Slide the locking switch down to release the tool
from its docking place, then pull the attachment
forward and away.
ON/OFF AND ROTATIONAL DIRECTION SWITCH
• The device is switched on and off by pressing and
releasing the ON/OFF switch. The harder the ON/OFF
switch is pressed, the faster the rotational speed.
• The direction of rotation switch is used to set the
direction of the drill chuck forward for screwing in
screws or backward for their removal. It is located
above the variable ON/OFF switch.
• To select the forward direction of rotation, press the
direction switch to the left (when viewed from the
rear).
• To select the backward direction of rotation, press
the direction switch to the right (when viewed from
the rear).
15
15.02.22 14:31 15.02.22 14:31