Publicidad
GB
CEMO UNI-Tank / MULTI-Tank 400 l
Tank documents and technical information,
Approval No.: Z-40.21-365
1.
Approval „OPERATOR EXCERPT" page
2. Transport, installation and
operating instructions
3. Inspection declaration
Important documents for the operator!
Please keep in a safe place!
(Documents are to be presented during inspections
of the tank system.)
1.
National Technical Approval
National
Technical
Approval
Approval number:
Z-40.21-365
Applicant:
Chemowerk GmbH
In den Backenländern 5, 71384 Weinstadt
Object of approval:
Blown polyethylene containers (PE-HD) in steel
collecting basins
400 l
Type: UNI 400 I
[Stamp]
The above object of approval is hereby granted National Technical Approval.
This National Technical Approval includes nine pages and five annexes with twelve pages.
The object first received national technical approval on 14 January 2005.
Deutsches Institut f
r Bautechnik [An institution supported by the German federal and state governments
ü
DIBt | Kolonnenstraße 30 L | D-10829 Berlin | Tel.: +4930 78730-0 | Fax:+4930 78730-320 | Email: dibt@dibt.de | www.dibt.de
8
page11
page11
DIBt
Deutsches Institut für Bautechnik
(DIBt)- German
Institute for Structural Engineering
AN INSTITUTION UNDER PUBLIC LAW
Approval office for constructed products and
types – Technical Inspection Office
Member of the European Organisation for Technical
Approvals (EOTA) and the Union Européenne pour
l'Agrément technique dans la construction (UEAtc).
Tel.: +49 30 78730-0 Fax: +49
30 78730-416 Email:
dibt@dibt.de
Date:
Code:
16. March 2010
I 55-1.40.21-12/10
Valid until:
15 January 2015
National Technical Approval
Z-40.21-365
8-10
1
The National Technical Approval certifies that the object of approval can be used and/or employed
within the meaning of the state building codes.
2
To the extent that the National Technical Approval has placed requirements in terms of special
knowledge and experience on the persons entrusted with the manufacture of constructed products
and types pursuant to § 17 Para. 5 of the Sample Building Code of the corresponding state
regulations, it should be noted that this specialist knowledge and experience can be attested by
equivalent documentation issued by other Member States of the European Union. This also applies
to attestations provided within the context of the Treaty establishing the European Economic
Community (EEC) or other bilateral agreements, if applicable.
3
The National Technical Approval does not replace the permits, approvals and certifications required
by law in connection with the realisation of building proposals.
4
The National Technical Approval is granted without prejudice to the rights of third parties, in
particular, private property rights.
5
Without prejudice to farther-reaching regulations contained in "Special Provisions," the
manufacturers and distributors of the approved object must make copies of the National Technical
Approval available to indirect and direct users of the approved object and notify them that the
National Technical Approval must be present at the place where the object is used. Upon request,
copies of the National Technical Approval must be made available to the agencies involved.
6
The National Technical Approval may only be reproduced in full. Publication of excerpts requires
permission from the Deutsche Institut für Bautechnik. Text and drawings used in advertising must
not contradict the National Technical Approval. Translations of the National Technical Approval must
bear the notice: "This is a translation of the German original and has not been reviewed by the
Deutsches Institut für Bautechnik."
The National Technical Approval is granted subject to revocation.
Approval are subject to subsequent additions and amendments, in particular, when new technical knowledge makes it
necessary.
National Technical Approval
Z-40.21-365
1
Approved object and area of application
(1)
The object of this National Technical Approval is factory-produced containers as
described in Annex 1, consisting of a polyethylene (PE-HD) interior container produced in a
blow-moulding process and an external container made of galvanised sheet steel (collecting
container). The containers are manufactured with a capacity of 400 litres. The containers stand
on steel feet. Four connection points are located on top of the container for filling, airing,
de-airing, protection against overfilling, and for emptying and fill-level monitoring.
(2)
The containers may only be placed as single containers within buildings, however not in
areas subject to risk of explosion in Zones 0 and 1.
(3)
The containers may be used for non-pressurised storage of the following liquids:
1
Heating oil EL grade pursuant to DIN 51603-1
2
Diesel fuel pursuant to DIN EN 590
3
Diesel fuel pursuant to DIN EN 14214
permeation-resistance
4
Lubricating oils, hydraulic oils, heat transfer oils (Q grade), mixed or unmixed with
flashpoint above 55 °C
5
Lubricating oils Hydraulic oils, used heat transfer oils 0, flashpoint above 55 °C; operator
must be able to document origin and flashpoint.
6
Standard commercial photo chemicals, in concentrations for use (new and used) with a
max. density of 1.15g/cm
The operational temperature may not exceed 30 °C.
(4)
The containers must be equipped with a leak detector that has been granted a national
technical approval.
(5)
This National Technical Approval cancels the requirement for the suitability
determination and type approval pursuant to § 63 of the German Water Management Act
4
[WHG]
for the approved object.
(6)
The period of validity of this National Technical Approval (see Page 1) is in relation to
use within the meaning of installation or set-up of the approved object, and not to later use.
2
Constructed product provisions
2.1
General
The containers and their parts must conform to the Special Provisions and the annexes of this
document, as well as the information filed with the Deutsches Institut für Bautechnik.
1
DIN 51603-1:2003-09, fluid combustibles – heating oils – part 1: Heating oil EL minimum requirements
2
DIN EN 590:2004-03, fuel for vehicles, diesel fuel, requirements and inspection methods, German version EN 590:2004
3
DIN EN 14214:2003-11, fuel for vehicles, fatty acid methyl esters (FAME) for diesel engines, requirements and inspection
methods, German version EN 14214:2003
4
German Act to regulate water resources (Water Management Act – WHG) of 31 July 2009.
DIBt
Page 2 of 11 | 16 March 2010
I. GENERAL PROVISIONS
The provisions of the National Technical
[Stamp]
DIBt
Page 3 of 11 | 16 March 2010
II. SPECIAL PROVISIONS
1
2
3
(biodiesel), only in containers equipped with
3
.
Publicidad
